Stimmen - 2, Durchschnittliche Bewertung: 3.5
(
)
)
|
Anleitung Zusammenfassung
Fig. 16Fig. 17 HOW TO OPERATE YOUR CORDLESS SWEEPER 4 7 1. Before using, please ensure that the cordless sweeper has been initially charged for 16-24 hours. Your cordless sweeper will only operate properly when the batteries are fully charged. Your sweeper will operate for varying lengths of time on a full charge. This will depend upon the type of surface being cleaned. (Longeroperating time on bare floors vscarpets.) 2. Push the On/Off switch to operate the unit. To turn off, press switch again. (Fig. 4) 3. To release the handle to a comfortable position, apply pressure to the top of the sweeper head with your foot while pulling back on the handle. (Fig. 5) "On/Off" switchFig. 4Fig. 5CAUTION: Any electronic or electrical appliance should not be stored in or exposed to areas of high heat or humidity. Do not store your cordless sweeper close to stoves, radiators, furnaces or in a bathroom or bathing area. 4. To change the speed of the sweeper, press on the speed control button. As you press on it, the speed indicator light will change. If one light lights up, then you have the low speed; two lights, medium speed; three lights, highspeed. 5. If the brush roll will jam, all the lights will flash and the unit will stop operating. If this occurs, please switch the unit off, clear obstruction from brush bar and then depress On/Off switch to start the sweeper again. Changing the Rotating Brush, Gear Box & SqueegeeWARNING: Use caution when changing the rotating brush and gear box so that the unit does not turn ON when pressing down on the sweeper power head. 1. Remove the extension tube handle from the sweeper power head. 2. Turn sweeper power head upside down being careful Notto accidentally turn the unit ON. 3. Remove the brush cover. (Fig. 10) (Refer to page 5 for detailed instructions.) 4. Push in on the locking tab of the gear box and lift gear box to remove. (Fig. 11 & Fig. 12) 5. Lift the brush bar end cap up from the slot. (Fig. 13) 6. Pull the brush bar out from the bushing and slip off the belt toremove the brush bar. (Fig. 14) 7. Insert the new brush bar by first inserting the brush bar into the bushing on the end opposite the driver belt. (Fig. 14) 8. Slip the belt over the brush bar cap. 9. Insert the brush bar into the slot. (Fig. 13) 10. Insert the gear box tabs into the tab slots and push down until it clicks into place. 11. To replace the squeegee, follow instructions above for removing the gear box and slide the squeegee out from left to right. (Fig. 15) Gear box tabsLocking tabLift Fig. 13Fig. 14Gear boxFig. 10Fig. 11Fig. 12Fig. 15 5 CHARGING THE CORDLESS SWEEPER Note: Your sweeper is highly advanced and has electronic controls that optimize the cleaning ability and durability of the sweeper. Please review the following instructions carefully to ensure that all features are utilized for best performance. 1. When charging the sweeper, the battery/charge indicator wil flash until the unit is fully charged and then turn steady. 2. When running the unit, the battery indicator will start as solidgreen, change to solid orange when approximately 70% of the battery life is used, and blink orange when in need of charging. The sweeper wil prevent the batteries frombeing deeply discharged and will indicate this by the battery indicator flashing, the headlights flashing, and the sweeper wil stop operating. This is normal and all that needs done is to recharge the sweeper fully. 3. When recharging from being fully discharged, the unit must charge for 1 hour minimum before it’s electronics will allow the unit to operate again. 6 NOTE: Peak performance may only be realized after the unit has been charged and discharged two ( 2) or three (3) times. IMPORTANT: To maintain peak performance of your cordless sweeper, it is recommended that the unit be fully discharged, then completely re-charged at least once a month. STORING THE CORDLESS Your cordless sweeper may be stored by using the slot on the back of the upper handle and hanging it from a screw secured to a wall or other vertical surface. Use a #6 flat or pan head screw with the appropriate hardware for the surface that the sweeper wil be mounted on, (i.e. gyproc). Allow the screw head to extend a approximately 3/16" from the mounting surface. Always empty yoursweeper before hanging up for storage. NOTE: If, when you place the sweeper to recharge and the charging indicator light does NOTilluminate, then press the On/ Off button once to turn the sweeper off. The charging indicator light should now light up. CLEANING THE DUST CONTAINERTo achieve the best performance, empty the dust container after each use. Fig. 6CAUTION: Do not accidentally turn unit on while cleaning. Do not clean while unit is charging. 1. Pull the dust container straight out from the side. (Fig. 6)2. Empty dust container contents. (Fig. 7) If desired- you may rinse with water to clean the dust container – but dry thoroughlybefore replacing on the sweeper. Fig. 73. Replace dust container on c...