Stimmen - 1, Durchschnittliche Bewertung: 4 ( )

Hersteller: MTD Dateigröße: 653.19 kb Dateiname: Unterrichtssprache:

After the desired clearance is obtained allow the adjust lever to spring back locking the trunnion in the proper positioning hole. Follow the same procedure for the opposite wheel. See figure 1. 2 LUBRICATION Figure 1 DUMPING OF SWEEPER Your sweeper can be dumped very easily without removing or disconnecting a part. Simply lift the hopper as shown and swing it over the sweeper and dump. See figure 2. A CAUTION If you are planning on dumping your Sweeper near a fire use care not to get too close, the brushes can be destroyed by excessive heat or flame. The bearings in your Sweeper have been prelubricated at the factory, however, it is recommended that a few drops of light oil should be added to the impeller and brush shaft bearings twice a year. Also, the wheels and pinions should be removed, the axles cleaned and an even coat of light oil applied. See figure 3. Bearing Figure 3 Figure 2 3 19468-6 19468-7 TMO-285A 197-468A and 63584 39 41 All Unnumbered Parts Interchangeable With Opposite Side. 4 PARTS LIST FOR MODELS 19468-6,19468-7, TMO-285A, 197-468A AND 63584 REF. NO. PART NO. DESCRIPTION REF. NO. PART NO. DESCRIPTION 1 4111-92 Assembly—End Plate R.H. *44 1538-6 Nut (5/16-18 Hex Lock) 2 1652-13 Bearing 45 4697-14 Draw—Bar—Front (R.H.) 3 1629-56 Retai ner— Beari ng 46 1552-14 Washer—Bowed 4 1530-6 Rivet (3/16 Dia. x 5/16) 47 1132-128 Ass’y-—Bracket & Pin 5 4111-91 Assembly—End Plate L.H. *48 769 Bolt (5/16-18x2-5/8 6 2120-69 Assembly—Pulley Hex Hd.) 7 2626-74 Pulley 49 4647-29 Frame Catcher—Lower 8 1548-12 Rollpin (.156 Dia. x1 Va) 50 4647-30 Frame Catcher—Upper 9 2651-49 Belt (3/8 Round Sect.) 51 0773-13 Basket—Fabric 10 1632-229 Shaft—Brush Drive (Short) 52 1513-87 Bolt—Shoulder (Pivot) 11 1650-21 Ring—Retainer *53 1538-13 Nut (3/8-16 Hex Lock) 12 1540-17 Washer—Flat (5/8x15/16 54 2603-77 Brace—Frame X1/16) 55 4709-24 Panel—Catcher Bottom 13 2632-231 Shaft—Brush Drive (Long) *56 1095 Screw (10-32x1/2 Philips) 14 4703-24 Baffle—Top 57 1694-26 Clamp *15 1507-12 Screw (10-32 x 1 -1 /8 Sems) *58 1507-6 Bolt (10-32 x 3/8 Truss Hd.) 16 3703-25 Baffle—Front *59 1534-8 Nut (10-32 Hex Lock) *17 1507-8 Screw (10-32 x 3/8 Sems) *60 1507-11 Screw (10-32 x 3/8 Sems) 18 3118-44 Assembly—Dust Cover R.H. 63 1513-93 Bolt (5/16x1-3/8 Special) Ю 2155-18 Assembly—Wheel Adj. 64 1694-34 Coupling—Half (Clamp) Lever 65 2723-4 Scraper—Impeller Pulley 20 2643-18 Knob—Wheel Adjust 66 1629-63 Retainer—Skirt 21 3118-45 Assembly—Dust Cover L.H. 67 1693-3 Skirt 22 1631-39 Axle—Wheel *68 1117 Screw (10-32 x 3/8 Phillips 23 1552-13 Washer—Bowed Hd.) 24 1657-45 Bushing—Spacer *69 1540-125 Washer (.59 x 1 -1 /8 x .015) *25 1038 Nut—Hex *70 70 Nut (5/16-18 Hex) 26 4622-98 Cover—Sweeper 71 1540-32 Washer (.78 x 1-1/4 x.015) 27 2679-2 Ass’y- Brush and Channel 72 1522-1 Screw (10-12x5/8 Sheet 28 2182-7 Assembly—Brush Retainer Metal) *29 1509-31 Bolt(1 /4-20 x 1-1 /8 Hex Hd.) 73 1509-90 Bolt (1/4-20 x 1V\ Hex Hd.) *...

Herunterladen

Geben Sie zwei Ziffern: