Stimmen - , Durchschnittliche Bewertung: ( )

Anleitung MTD, modell 242-675-000

Hersteller: MTD
Dateigröße: 1.37 mb
Dateiname: f3b0a6ef-9529-8af4-69d4-a4590ceaf8d8.pdf

Unterrichtssprache:

Das Dokument wird geladen, bitte warten

HerunterladenSchließen

Das Dokument wird geladen, bitte warten

HerunterladenSchließen

Wipe off any ¡pilled fuel before starting engine. 5. Do not change engine governor settings. 6. Do not put hands near rotating parts for any reason. 7. If the power vacuum should start to vibrate abnormal!;, stop the engine and check immediately for the cause. Vibration is generally a warning of trouble. 8. Before cleaning, repairing or inspecting, make certain all moving parts have come to a complete stop. Disconnect spark pk g wire and keep wire away from plug to prevent accidental starting. Also keep throttle control lever in the stop position. 9. If the power vacuum should become blocked with debris a: any point, shut engine off and wait until the impeller comes to a cor iplete stop before attempting to remove the obstruction. Disconnect spark plug wire to prevent accidental starting. 10. Check all bolts for tightness at frequent periods. 11. Never store this power vacuum with fuel in the tank. Allow engine to cool before storing in any enclosure. 12. Keep bag and equipment free of debris when not in use. 13. Never operate this power vacuum unless air duct and vacuum bag are properly affixed in their place. Large zippered end of bag must be closed when operating to prevent objects from being blown out. 14. Never empty vacuum bag when engine is running. 15. Never change inlet nozzle or auxiliary hose attachment when engine is running. 16. The manufacturer recommends that the operator wear safety glasses or some other suitable eye protection when operating this machine. 17. Check the vacuum bag frequently for wear and replace when necessary. 18. Never operate as a leaf blower unless impeller guard and guard assembly are properly affixed in their place. 19. Exercise caution whenever operating as a leaf blower. Do not allow discharge to be pointed in the direction of persons. 20. No one should operate this unit while intoxicated or while taking medication that impairs the senses or reactions. _CONTENTS OF HARDWARE PACK__ (Hardware pack may contain extra items which are not used on your unit. Quantities of parts and part number > are shown in parentheses.) ATTACHING THE NOZZLE AND AIR DUCT ASSEMBLY Hand Knobs (Qty. 3) (720-0170) Cupped Washers (Qty. 3) (736-0242) Flat Washers (Qty. 2) (736-0231)— B ATTACHING THE UPPER HANDLE 1 Hex Bolts 1/4-20 x 1-3/4" Long (Qty. 4) (710-0136) He:t Lock Nuts 1/4-20 Thread (Qty. 4) (712-0107) INSTALLING THE BAG T Stu d Pins (Qty (711-0737) Push-On Speed Nuts (Qty- 2) (1539-019) ATTACHING THE CLUTCH ROD (Self-Propelled Units Only) Clutch Grip and Extension/_. Spring are Not Shown ( ) Clevis Pin (Qty. 1) (711-0679)- Hairpin Clip (Qty. 1) (714-0145) Hex Lock Nut 1/4-20 Thread (Qty-1) (712-0107) Hex Jam Nut 1/4-20 Thread (Qty. 1) (712-0298) (Thinner Nut) I ( I ! I i I I I I I i I I I I I I I I I I I I FIGURE 1. 0 12 3 INCHES ASSEMBLY INSTRUCTIONS IMPORTANT: This unit is shipped WITHOUT GASOLINE or OIL. After assembly, service engine with gasoline and oil as instructed in the separate engine manual packed with your unit. Upper Nozzle :—-—Air Duct -Assembly Directional Discharge Assembly Impeller Guard Clutch Rod (Self-Propelled Models Only) FIGURE 2.-Loose Parts in Carton E— C~*@ FIGURE 3. G- ^c!I$ Nozzle NOTE: Reference to right or left hand side of the vacuum is observed from behind the unit in the operating position. UNPACKING Remove the vacuum, loose parts, hardware pack and literature from the carton. Make certain all parts and literature have been removed before the carton is discarded. LOOSE PARTS IN CARTON -(See Figure 2) (1) Nozzle (1) Upper Handle (1) Air Duct Assembly (1) Clutch Rod (Self-Propelled Models Only) (1) Directional Discharge Assembly (1) Impeller Guard (1) Bag TOW BAR KIT Standard for push models, optional for self-pro-pelled models. -(See Figure 3) Hex Bolts 5/16-18 x 1” Long Hex Nut 5/16-18 Thread Truss Machine Screw 1/4-20 x 3/4 Lock Washer 1/4” I.D. Hex Nut 1/4-20 Thread Shoulder Bolt Cupped Washers 3/8” I.D. Hex Jam Lock Nut 3/8-16 Thread ATTACHING THE NOZZLE (Hardware A) Place nozzle in position on front of housing so that it rests in flanges. Secure with one hand knob and cupped washer (cupped side of washer against the -nozzle). See figure 4. A (2) B (4) C (2) D (1) E (1) F (1) G 0) H (2) I (1) (2) I I 1 FIGURE 4. Upper Handle ATTACHING THE UPPER HANDLE (Hardware B) Place the upper handle in position over lower handle. Fasten with four hex bolts and lock nuts provided. -See figure 5. Two 7/16” wrenches are required. FIGURE 5. 3 I Hand Knob Cupped .Washer ATTACHING THE AIR DUCT ASSEMBLY (Hardware A) Place air duct assembly over opening on top of housing. Secure with two flat washers, cupped washers (cupped side of washers against flat washers) and -hand knobs. See figure 6. FIGURE 6. INSTALLING THE BAG (Hardware C) 1. Place the stud pins in holes in upper handle (head of pins go to the inside of handle). Secure pins wi...