Stimmen - 3, Durchschnittliche Bewertung: 4.3 ( )

Hersteller: Poulan Dateigröße: 853.5 kb Dateiname: NOUS2003_151673.pdf Unterrichtssprache:

To protect grass catcher (1) Lower Chute (1) Cover Seal cover during assembly place cover upsidedown on (1) Support Post (1) Bag of Parts overturned carton. (1) Owner's Manual • Check carton contents against list. Be sure all parts are there. NOTE: For ease of assembly, aside of your work area, lay out all hardware in the following groups. Each step of the assembly instructions will identify the group needed for that step. GROUP "A" ASSEMBLY LOCATION HARDWARE SHOWN ACTUAL SIZE BAG OF PARTS CONTENTS GROUP "B" REAR MOUNTING BRACKET AND SUPPORT PLATE TO DRAW BAR (6) Bolt 7/16 - 14 x 3/4 Self Tapping SUPPORT POSTS TO COVER ASSEMBLY (2) Bolt 5/16 - 18 x 3/4 (4) Locknut 5/16-18 (2) Bolt 5/16 - 18 x 2-1/4 4 BAG OF PARTS CONTENTS (continued) GROUP "E" GROUP "C" CHUTE LATCH ASSEMBLY to UPPER CHUTE (1) Screw #10 x 1-1/8 (2) Washer 3/16 x 3/4 x 16 Ga. (1) Nut, Acorn #10 (1) Spacer, Split #10 (1) Rubber Latch LOWER CHUTE ASSEMBLY TO MOWER DECK GROUP "F " CHUTE LATCH ASSEMBLY to LOWER CHUTE (2) Nut, Weld #10 (2) Washer, Lock #10 (2) Washer 3/16 x 3/4 x 16 Ga. (2) Screw #10 x 5/8 (2) Latch Hook Assembly (1) Nut, Weld #10 (1) Washer, Lock #10 (1) Washer 3/16 x 3/4 x 16 Ga. (1) Screw #10 x 5/8 SUPPORT POSTS TO MOUNTING BRACKET (2) Support Clevis Pin (2) Retainer Spring (4) Tubing End Caps GROUP "D" 5 PARTS IDENTIFICATION ASSEMBLY COVER WARNINGDonotoperatemowerunlesscontainerisproperlyissubjecttowearanddetierioration.Checkbagfrequently.Replacewhencrackedordamaged.Useonlyarecommendedreplacementcontainer. WARNINGDonotoperatemowerunlesscontainerisproperlyissubjecttowearanddetierioration.Checkbagfrequently.Replacewhencrackedordamaged.Useonlyarecommendedreplacementcontainer. WARNINGDonotoperatemowerunlesscontainerisproperlyissubjecttowearanddetierioration.Checkbagfrequently.Replacewhencrackedordamaged.Useonlyarecommendedreplacementcontainer. 02079UPPER CHUTE CHUTE LATCH DUMP BAG INDICATOR LOWER CHUTE GRASS CATCHER CONTAINERS LOWER CHUTE ATTACHING STRAPS NOTE: When right hand (R.H.) and left hand (L.H.) are mentioned in this manual, it means when you are seated on the tractor, in the operator's position. (1) 1/2" Wrench (1) 3" or longer Ex ten sion THESE ARE THE TOOLS YOU WILL NEED TO ASSEMBLE YOUR GRASS CATCHER: (1) 1/2" Socket (1) 5/8" Socket (1) Drive Ratchet (1) Short Handle Phillips Screwdriver CAUTION: BEFORE ASSEMBLING GRASS CATCHER TO TRACTOR: • Depress clutch/brake pedal fully and set parking brake. • Place gearshift/motion control lever in "NEUTRAL" position. • Place attachment clutch in "DISENGAGED" position. • Turn ignition key "OFF" and remove key. • Make sure the blade and all moving parts have completely stopped. • Disconnect spark plug wire from spark plug and place wire where it cannot come in contact with plug. 6 7 SUPPORT POST (See Fig. 3) Use Hardware - - GROUP "B" 1. Rotate cover assembly onto its side as shown. 2. Secure support tubes to cover assembly using short hex bolts, long hex bolts, and locknuts as shown. Tighten all hardware securely. 02086 02357 1 REAR MOUNTING BRACKET and SUPPORT PLATE (See Figs. 1A & 1B) Use Hardware - - GROUP "A" 1. Install support plate to inside of drawbar as shown, using two (2) 7/16-14 x 3/4 hex bolts and the two threaded upper holes in the plate. Do not tighten at this time. NOTE: Be sure to align the four (4) lower threaded holes of the support plate with the holes in the drawbar. 2. Assemble the mounting bracket as shown to the out side of the drawbar using four (4) 7/16-14 x 3/4 hex bolts and the four (4) lower threaded holes of the support plate. Tighten all hard ware securely. Fig. 1B COVER SEAL (See Fig. 2) No hardware required 1. Align mark on seal with mark at cover opening. 2. Work seal into opening so cover sits between fl anges of seal. 2 3 ALIGNMENT MARKS COVER SEAL Fig. 2 DRAWBAR HEX BOLTS THREADED UPPER HOLES SUPPORT PLATE Fig. 1A HEX BOLTS SUPPORT PLATE DRAWBAR THREADED LOWER HOLES MOUNTING BRACKET 02356 LOCKNUTS LOCKNUTS SUPPORT POSTS LONG HEX BOLTS SHORT HEX BOLTS COVER ASSEMBLY Fig. 3 8 02360 MOUNTING TO TRACTOR (See Fig. 4) Use Hardware - - GROUP "C" NOTE: For ease of assembly, you may wish to obtain the as sis tance of another person for mounting assembly to tractor. 1. Raise seat on tractor to allow assembly to be mounted. 2. With cover closed, lift assembly and place support posts into mount ing bracket. Allow assembly to rest on bottom of mounting bracket. 3. Line up holes in mounting bracket with holes in support posts and insert support post clevis pins. Secure with re tain er springs. 4. Install the four (4) tubing end caps onto container support. Tap each end cap onto container support tubes to seat securely. 4 COVER AS SEM BLY Fig. 4 END CAP SUPPORT POST MOUNTING BRACKET SUPPORT POST CLEVIS PINS RE TAIN ER SPRINGS DRAWBAR CONTAINER ASSEMBLY (See Fig. 5) No hardware required 1. Place bottom half inside of top half, as shown. 2. Place one foot inside bottom half and lift top half to meet bottom half. 3. Press halves tightly together while lifting t...

Herunterladen

Geben Sie zwei Ziffern: