Stimmen - 6, Durchschnittliche Bewertung: 3.8 ( )

Hersteller: Poulan Dateigröße: 758.93 kb Dateiname: NOUS2005_532402349.pdf Unterrichtssprache:

8 3 4 CAUTION: BEFORE ASSEMBLING GRASS CATCHER TO TRACTOR: • Depress clutch/brake pedal fully and set parking brake. • Place gearshift/motion control lever in "NEUTRAL" position. • Place attachment clutch in "DISENGAGED" position. • Turn ignition key "OFF" and remove key. • Make sure the blade and all moving parts have completely stopped. • Disconnect spark plug wire from spark plug and place wire where it cannot come in contact with plug. NOTE: When right hand (R.H.) and left hand (L.H.) are mentioned in this manual, it means when you are seated on the tractor, in the operator's position. KNOW YOUR GRASS CATCHER READ THIS OWNER'S MANUAL AND SAFETY RULES BEFORE ASSEMBLING OR OPERATING YOUR GRASS CATCH ER. Compare the illustrations with the carton contents to familiarize yourself with the parts before starting the assembly. Study the operating instructions and safety precautions thoroughly to insure proper functioning of your Grass Catcher and to prevent injury to yourself and others. Save this manual for future reference. The operation of any tractor can result in foreign objects thrown into the eyes, which can result in severe eye damage. Always wear safety glasses or eye shields be fore starting your trac tor and while mow ing. We recommend a wide vision safety mask for over the spec tacles or stan dard safety glasses. 00155 03021 LOWER CHUTE ATTACHING STRAPS PARTS IDENTIFICATION UPPER CHUTE CHUTE LATCH FULL BAG INDICATOR LOWER CHUTE GRASS CATCHER CONTAINERS COVER ASSEMBLY UNPACKING INSTRUCTIONS • Remove all parts and packing materials from carton. • Check carton contents against list. Be sure all parts are there. CARTON CONTENTS: (3) Container Tops (3) Container Bottoms (1) Upper Chute (1) Lower Chute (1) Cover Assembly (3) BLADES TOOLS REQUIRED FOR ASSEMBLY - (1) 5/8" Wrench (for changing Blades) RETAINER SPRING SUPPORT ASSEMBLY Marked "A" SUPPORT ASSEMBLY Marked "B" 5 3 MOUNTING COVER ASSEMBLY TO SUPPORT ASSEMBLY (See Fig. 3) NOTE: For ease of assembly, you may wish to obtain the as sis tance of another person for mounting cover assembly to tractor. 1. Position cover assembly on ground behind tractor. 2. Lift and rotate cover to align cover brackets with support assembly tubes. 3. Slide cover assembly down onto the support tubes. FIG. 3 03024 COVER ASSEMBLY SUPPORT ASSEMBLY ASSEMBLY 02543 HANG SUPPORT ASSEMBLY ON REAR DRAWBAR (See Fig. 2) Determine the correct support assembly for your tractor. The support assemblies are marked "A" and "B". Compare the drawbar illustrations below to the drawbar located at the rear of your tractor. Use the support assembly indicated for your tractor and discard the other support assembly. 2 FIG. 2 INSERT FLANGES FIRST INTO DRAWBAR SLOTS SUPPORT ASSEMBLY DRAWBAR SLOTS (Drawbar "A" shown) RETAINER SPRING PIN 02051 02051 INSTALL HIGH LIFT BAGGING BLADES (See Fig. 1) CAUTION: Blades are sharp. Protect your hands with gloves and/or wrap blade with heavy cloth. NOTE: If you already have high lift bagging blades on your mower, store the supplied blades in a safe place for future use. Go on to step 2. 1. Raise mower to highest position to allow access to blades. 2. Remove blade bolts by turning counterclockwise. 3. Install bagging blades supplied with stamped "THIS SIDE UP" facing up towards mower, or, blades stamped with "GRASS SIDE" facing down towards grass. IMPORTANT: To ensure proper assembly, center hole in blade must align with star pattern on mandrel assembly. 4. Install and tighten blade bolts securely (45-55 Ft. Lbs. torque). 02544 HIGH LIFT BAGGING BLADE BLADE BOLT (SPECIAL) MANDREL ASSEMBLY FIG. 1 STAR PATTERN 1 02051 DRAWBAR PIN HOLE 1. Slide fl anges of support assembly into drawbar slots fi rst, then, pivot backwards inserting pin into drawbar pin hole. 2. Be sure support assembly is seated properly, then secure with retainer spring. DRAWBAR A Use Support Assembly Marked "A" DRAWBAR B Use Support Assembly Marked "B" 6 CONTAINER MOUNTING (See Fig. 5) 1. Install one container to left side fi rst with warning to outside of unit. Install another container to center position and one in right position. NOTE: Right con tain er should always over lap left con tain er at center supports. 2. Close cover and lock latch handles over center support tubes. 5 FIG. 5 CONTAINER ASSEMBLY (See Fig. 4) 1. Place bottom half inside of top half, as shown. 2. Place one foot inside bottom half and lift top half to meet bottom half. 3. Press halves tightly together while lifting top to lock into place as shown. IMPORTANT: BEFORE LOCKING THE TABS, HOOKED EDGES ON BOTH HALVES MUST OVERLAP TO FORM SEAL AS SHOWN IN INSET. 4. Repeat for other containers. PRESS TOGETHER TO FORM SEAL WHILE LIFTING TOP HALF 02089 CONTAINER BOTTOM HALF CONTAINER TOP HALF ASSEMBLY CHECK: Squeeze sides of lower half of contain er and check that there is no gap between upper and lower halves. If a gap appears, unlock tabs to separate container halves and repeat instructions above. LOCKING TAB WARNING Donotoperatemowe...

Herunterladen

Geben Sie zwei Ziffern: