Stimmen - 3, Durchschnittliche Bewertung: 4
(
)
)
|
Anleitung Zusammenfassung
2. GASOHOL – It can cause deterioration of rubber and/or plastic parts and disruption of engine lubrication. 3. OIL FOR 4-CYCLE ENGINE USE or WATER COOLED 2-CYCLE ENGINE USE – It can cause spark plug fouling, exhaust port blocking, or piston ring sticking. 4. Mixed fuels which have been left unused for a period of one month or more may clog the carburetor or result in the engine failing to operate properly. . 8. Operation The RedMax stick edger Model HE2601 is designed for edging lawn in gardens, parks, roadsides and so on. Before starting the engine, take the operating position and adjust the handle position and the wheel height as necessary. n ADJUSTING HANDLE POSITION • Loosen the handle bracket screws and reposition the handle to your best operating position. Re-tighten the screws. n ADJUSTING WHEEL HEIGHT • Loosen the clamp lever and change the wheel height to obtain desired cutting depth. WARNING • Never adjust wheel height with the engine running. n STARTING ENGINE 1. Rest the unit on a flat, firm place. Keep the blade off the ground and clear of the surrounding as it will start rotating upon starting of the engine. 2. Pump the priming pump until fuel flows out in the clear tube. 3. Move the choke lever upward to close the choke. 4.Set the ignition switch to the “start” position. While pulling the throttle lever, push the set button, and release the throttle, then the throttle lever is in to the “start” position. START STOP Ignition Switch Throttle set Button . 9. Operation 5. While pulling the throttle trigger with the n STOPPING ENGINE little finger of your left hand, pull the starter 1.Release the throttle trigger and run the rope. engine for a half minute. 2.Shift the ignition switch to the STOP position. NOTE • Avoid pulling the rope to its end or returning it by releasing the knob. Such actions can cause starter failures. 6. When the engine has started, move the choke lever gradually downward to open the choke. 7. Allow the engine to warm up for a half minute before starting operation. NOTE NOTE • Except for an emergency, avoid stopping the engine with the trigger pulled on. ¦ ADJUSTING IDLING SPEED 1. When the engine tends to stop frequently at idling mode, turn the adjusting screw clock-wise. 2. When the cutting head keeps rotating after releasing the trigger, turn the adjusting screw counter-clockwise. NOTE 1. After setting up the unit, check play of the throttle cable. The normal play is between .04" and .08" (1mm and 2mm). 2. Warm up the engine before adjusting the idling speed. 1. When restarting the engine immediately after stopping it, leave the choke open. 2. Overchoking can make the engine hard to start due to excess fuel. When the engine failed to start after several attempts, open the choke and repeat pulling the rope, or remove the spark plug and dry it. . 10. How to use WARNING 1. A l w a y s wear eye protection such as safety goggles. Never lean over the rotating cutting head. Rocks or other debris could be thrown into eyes and face and cause serious personal injury. 2. Keep the blade guard and the mad guard attached in place at all times when the unit is operated. 3. Before starting a job, check the area and remove all obstacles and objects that could be thrown by the blade. 4. Do not adjust the wheel height or try to remove anything entangled to the blade with the engine running. 1. Before starting the engine, adjust the wheel height for desired cutting depth(See page 9). 2. Before starting a job, plan your direction of travel so that you can always hold the edger on you right side and can walk on a hard surface as much as possible. 3. When starting to edge, run the engine at full throttle, and slowly have the blade cut into the edge groove. NOTE • Do not use the HE2601 to make a new groove into the ground. Such usage will not be covered by RedMax Warranty. . 11. Maintenance WARNING • Always be sure to stop the engine before inspecting the stick edger for problems or performing maintenance. • Never alter the stick edger or take the engine apart. • When replacing parts, always be sure to use only RedMax products or products which have been certified by RedMax for use with the RedMax stick edger. • Things to check before using stick edger n BE SURE TO CHECK THE FOLLOWING BEFORE USING YOUR STICK EDGER Item to be checked Response 1 Edging mechanism • See if attachment is loose • Check if edges of blades are dull • Tighten screws and bolts • Sharpen or replace blades 2 Throttle • Stiff and difficult to move • Repair or replace 3 Throttle wire • Too loose, too tight • Stiff and difficult to move • Adjust • Repair or replace 4 Engine attachment • See if fittings are loose • Tighten fittings 5 Fuel tank • See if attachment is loose • See if fuel pipe is damaged • See if cap packing is damaged • Tighten screws and bolts • Replace • Replace 6 Muffler • See if attachment is loose • Tighten screws and bolts n REGULAR MAINTENANCE INSPECTION Check the stick edger for damage or problems at th...