Stimmen - 2, Durchschnittliche Bewertung: 4.5
(
)
)
|
Anleitung Zusammenfassung
C. Move Control Levers to neutral position and then to the “OUT” position. D. Set the parking brake. E. Turn ignition key to “OFF” position. F. Remove the key and wait for all movement and sound to cease before dismounting. ANTI-SCALP ROLLER WARNING Use EXTREME caution when mowing and/or turning on slopes as loss of traction and/or tip-over could occur. Drive slower on slopes. DO NOT mow slopes greater than 15 degrees. Watch for ditches, holes, rocks, dips and rises, which change the operating angle. Keep away from drop-offs and steep banks. Avoid sudden starts when mowing uphill -mower may tip backwards. Loss of traction may occur going downhill -weight transfer to the front wheels may cause drive wheels to slip and cause loss of braking. DO NOT mow slopes when grass is wet -slip- pery conditions affect steering and reduce traction and braking. The operator is respon- sible for safe OPERATION ON SLOPES. CASTER ASSEMBLY (Standard on 73” decks, optional on 61” decks) RollerHeightAdjustmentHoles Spacers may be positioned above and/or below the caster arm to adjust position. 13 WARNING AVOID SERIOUS INJURIES TO OTHERS: ALWAYS REMOVE THE KEY FROM THE IGNI- TION SWITCH WHENEVER THE MOWER IS UNATTENDED TO PREVENT CHILDREN OR UNAUTHORIZED PERSONS FROM STARTING THE ENGINE. 16. PUMP BYPASS-TO MOVE THE TRACTOR WITHOUT POWER: The pump bypass valves are located on the forward sides of each pump. Turn the control clockwise two complete turns to release the pump for free wheeling; turn them counter-clockwise to resume operation. Pumps as seen from above. Use a rod through the hex head, or a 5/8” wrench to openor close the valve. ElectricalFuses Hydrostatic Fluid Engine Oil Reservoir Filler Cap NOTE: To move the tractor without power, the pumps must be unlocked and in the free wheel posi- tion. Failure to do so could possibly damage the hydraulic motors. Never pull at more than 2 MPH. 17. FUEL TANK SELECTOR VALVE: Located on the front panel below the operator is the fuel directional valve. This valve has three positions for operations and each position is made in 1/4 turn increments. This directional valve has a shut off position and can be used when the machine will not be used for a few days or when the unit is transported to and from a work site. Fuel Flow Valve Position EFI Valve Position Off Down Right Right Tank Right Down Left Tank Left Left MOWING RECOMMENDATIONS 1. Keep mower blades sharp. 2. Make sure deck and discharge chute are clean. 3. Pivoting Front Axle Settings -The Professional Series pivoting front axle increases operator comfort, traction, mower life and improves quality of cut. In some conditions stopping the front axle from pivoting will improve the evenness of the cut. It can also reduce scuffing of the anti-scalp rollers when mowing on uneven terrain.To set the front axle in a fixed position, move the lock- ing pins to the outer positions. (See page 21) DANGER TO AVOID SERIOUS INJURY FROM BLADE CONTACT, POWER MUST BE OFF TO CLEAN DISCHARGE CHUTE. KEEP HANDS AND FEET AWAY FROM UNDERNEATH MOWER TO AVOID SERIOUS INJURY OR DEATH. WARNING ROTARY MOWERS CAN DISCHARGE OBJECTS AT HIGH SPEEDS. TO AVOID SERIOUS INJURIES OR DEATH: J ll OPERATE ONLY WITH SIDE BANDS IN GOOD REPAIR AND CHUTE OR GRASS CATCHER ATTACHMENT INSTALLED. J ll KEEP CHILDREN, PETS, AND BYSTANDERS AWAY FROM THE WORK AREA. J ll DO NOT OPERATE MOWER IN THE VICIN- ITY OF OTHER PERSONS. J ll DISCHARGE AWAY FROM BUILDINGS, WALLS OR OTHER STRUCTURES. Fuel Tank Operator Weight Seat Slide Site Lines Adjustment Knob Release Lever Cutting Height DC Power Outlet Adjustment Pin Fuel Tank Selector Valve ParkingBrakeLever 14 SECTION III MAINTENANCE CAUTION BEFORE PERFORMING ANY MAINTENANCE, TURN OFF ENGINE, REMOVE KEY AND DISCONNECT SPARK PLUGS. USE EXTREME CARE WHEN WORKING ON MACHINERY. DO NOT WEAR WATCH OR JEWELRY. DO NOT WEAR LOOSE FITTING CLOTHES, AND OBSERVE ALL COMMON SAFETY PRACTICES WITH TOOLS. IMPORTANT: BEFORE PERFORMING ANY SERVICE, MAINTENANCE OR REPAIR ON THE ENGINE, REFER TO THE RESPECTIVE ENGINE MANUFACTURERS’ MANUAL FOR SPECIFIC INFORMATION CONCERNING YOUR PARTICULAR BRAND OF ENGINE. MAINTENANCE SCHEDULE SERVICE WHEN Check crankcase oil level_______________________________________________________before each use Check air intake screen__________________________________________________________after each use Clean grass from under deck _____________________________________________________after each use Check tire pressure ____________________________________________________________every 10 hours Sharpen mower blades _________________________________________________________every 10 hours Clean air filter element ___________________________________________________________every 8 hours Check 20W50 motor oil in hydrostatic system ___________________________________________________________every 10 hours Check drive belts ______________________________________________________________every 50 hours (20 hr break-in) Grease blade spindles _________...