Stimmen - 2, Durchschnittliche Bewertung: 4.5
(
)
)
|
Anleitung Zusammenfassung
_;::, /* / / CAUTION: Before using this product, read this manual and follow all Safety Rules and • Safety Operating Instructions. • Assembly • Operation • Maintenance IMPORTANT -READ THIS FIRST!!! • Parts For Missing Parts or Assembly Questions Please Call 217-728-8388 Mon.-Fri. 7 am -5 pm CST. FAX 217-728-2032 or e-mail info@agri-fab.com Missing parts will be sent UPS in 24 hours directly to your home. Sears, Roebuck and Co., Hoffman Estates, IL 60179 U.S.A. PRINTED IN U.S.A. FORM NO. 47725 (REV. 4/03) Any power equipment can cause injury if operated improperly or if the user does not understand how to operate the equipment. Exercise caution at all times, when using )ower equipment. • Refer to your tractor owners manual for "Rules A, Look for this symbol to point out importantFor Safe Operation". A safety precautions. It mean--Attention!! i Become alert!! Your safety is involved. Your bumper carton contains parts listed below. Identify and lay out all parts shown. Place plug on a work bench or solid table. Set end of bumper onto plug until it rests on short step of plug. Using even pressure, push down on bumper until end of bumper slips over plug. See figure 1. BUMPER PUSH DOWN WITH EVEN PRESSURE WORK BENCH OR SOLID TABL_ L FIGURE 1 HARDWARE SHOWN FULL SIZE (LT & YT) LAWN TRACTORS Ref. Part Qty. Description No. No. cool down before proceeding with bumper ,_ CAUTION! Muffler is hofl Allow engine to A 48894 2 Hex Bolt, Self Threading installation. 3/8-16 x 1-1/2" B 43062 4 Hex Bolt, 3/8-16 x 1-1/2" • Remove tractor hood. C 43O7O 4 Flat Washer, 3/8" • If your tractor has a heat shield like the one in figure D 43003 4 Lock Washer, 3/8" 2 remove it to attach bumper, then reinstall shield. E 43015 4 Hex Nut, 3/8-16 Thd. F 44742 2 Plug REMOVE BOLTS G 24655 2 Bumper Extension Brackets 64623 1 Bumper Assembly MUFFLER HEAT SHIELD / TOOLS REQUIRED (2) 9/16" Open End or Box Wrenches FIGURE 2 2 • Remove bolts from mounting holes in tractor frame. See figure 3. • Attach extension bracket to rear mounting hole in frame using a 3/8" x 1-1/2" hex bolt, flat washer and lock washer. Be sure bracket is turned as shown in figure 3. Do not tighten yet. • Slide bumper onto extension brackets. Align slots in bumper and extension brackets and fasten to frame using two 3/8" x 1-1/2" hex bolts, flat washers and lock washers. Push bumper down for hood tilt clearance and then tighten all bolts. See figure 3. NOTE 1: If bolts cannot be inserted into or screwed into front mounting holes in tractor frame, use self threading bolts. NOTE 2: If bolts can be inserted freely into mounting holes in tractor frame, they must be secured with lock washers and hex nuts on inside of tractor frame. HEX NUTAND EXTENSION LOCK WASHER BRACKET (SEE NOTE 2) USE THESE WASHER HOLES (SEE NOTE 2) HEXBOLT FLAT WASHER BRACKET ON SOME MODELS FIGURE 3 (GT) GARDEN TRACTORS CAUTION! Muffler is hofl Allow engine to cool down before proceeding with bumper installation. Remove tractor hood. Unscrew bolts from mounting holes in tractor frame. If bolts are secured by hex nuts that you cannot reach, remove heat shield. For access to hex nuts, slide muffler down exhaust tubes to rest on top of browning shield. Replace muffler and heat shield after assembling bumper. See figure 4. , REMOVE BOLTS IFFLER HEAT SHIELD EXHAUSTT_BES MUFFLER" / rHESE BOLTS BROWNING SHIELD FIGURE 4 Fasten bumper to frame using four 3/8" x 1-1/2" hex bolts, lock washers and flat washers. Do not tighten yet. See figure 5. Push bumper down for maximum clearance, then tilt hood forward. If hood remains stable when tilted forward, tighten the hex nuts that fasten the bumper to the frame. See figure 5. NOTE 1: If bolts cannot be inserted into or screwed into front mounting holes in tractor frame, use self threading bolts. NOTE 2: If bolts can be inserted freely into mounting holes in tractor frame, they must be secured with lock washers and hex nuts on inside of tractor frame. LOCK WASHER FLAT WASHER AND HEXNUT (SEE NOTE 2) LOCK WASHER (SEE NOTE2) HEX BOLT (SEE NOTE 1) FIGURE 5 Get it fixed, at your home or ours! For repair of major brand appliances in your own home... no matter who made it, no matter who sold it! 1-800-4-MY-HOM EsMAnyt,me, day or n,ght (1-800-469-4663) To bring in products such as vacuums, lawn equipment and electronics for repair, call for the location of your nearest Sears Parts & Repair Center. 1-800-488-1222 Anytime, day or night For the replacement parts, accessories and owner's manuals that you need to do-it-yourself, call Sears PartsDirect sM! 1-800-366-PART 6am-11pmCST, (1-800-366-7278) 7 days a week To purchase or inquire about a Sears Service Agreement: 1-800-827-6655 7 a.m. -5 p.m. CST, Men. -Sat. Para pedtr serv_cto de reparacion a domictho, Au Canada pour service en fran(_als' y para ordenar ptezas con entrega a dom_c_lio' 1-877-LE-FOYER sM 1-888-SU-HOGAR sM (1-877-533-6937) (1-888-784-6427) SEAR...