Stimmen - 5, Durchschnittliche Bewertung: 4.6
(
)
)
|
Anleitung Zusammenfassung
,, Operation ,, Maintenance ,, Parts Sears, Roebuck and Co., Hoffman Estates, IL 60179 U.S.A. PRINTED IN U.S.A. FORM NO. 42187 (12/11/08) WARRANTY .................................................................... 2 OPERATION .................................................................... 5 SAFETY RULES .............................................................. 2 REPAIR PARTS ILLUSTRATION ..................................... 6 CARTON CONTENTS ..................................................... 3 REPAIR PARTS LIST ....................................................... 7 FULL SIZE HARDWARE CHART .................................... 3 PARTS ORDERING/SERVICE ...................... BACK PAGE ASSEMBLY ...................................................................... 4 ONE YEAR FULL WARRANTY When operated and maintained according to all supplied instructions, if this Craftsman product fails due to a defect in material or workmanship within one year from the date of purchase, return it to any Sears store or other Craftsman outlet in the United States for free replacement. This warranty applies for only 90 days if this product is ever used for commercial or rental purposes. This warranty gives you specific legal rights, and you may also have other rights which vary from state to state. Sears, Roebuck and Co., D817WA, Hoffman Estates, IL 60179 Any power equipment can cause injury if operated improperly or if the user does not understand how to operate the equipment. Exercise caution at all times when using power equipment. • Refer to your tractor owners manual for "Rules For Safe Operation". Look for this symbol to point out important safety precautions. It means --Attention!! Become alert!! Your safety is involved. The model number and serial numbers will be found on a MODEL NUMBER: 486.24628 decal attached to the Brush Guard. SERIAL NUMBER: You should record both the serial number and the date of DATE OF PURCHASE: purchase and keep in a safe place for future reference. 2 Call 1-866-576-8388 for missing parts or assembly help DO NOT RETURN TO STORE C \ REF QTY DESCRiPTiON REF QTY DESCRiPTiON 1 4 iBrush Guard 3 2 Frame Brace 2 2 Latch m q ______-I J J J i J / _____--/ i J i J / J f J / I J J / i J f 7 _'F 8 [__ _ 9 ___ 10 REF QTY DESCRiPTiON REF QTY DESCRiPTiON 1 4 Carriage Bolt, 3/8-16 x 1" 6 2 Washer, .5312 x 1 x .0598" 2 2 Hex Bolt, 3/8-1 x 1" 7 2 Spring 3 2 Hex Bolt, 1/4-20 x 1-1/4" 8 4 Hex Nut (SIMS), 1/4" 4 2 Shoulder Bolt, 3/8-16 9 4 Lock Nut, 3/8" 5 2 Washer, 3/8" 10 4 Whizlock Nut, 3/8" Call 1-866-576-8388 for missing parts or assembly help DO NOT RETURN TO STORE TOOLS REQUIRED FOR ASSEMBLY (2) 7/16" Wrenches (2) 9/16" Wrenches (1) 3/4" Wrench CAUTION! Muffler is hot! Allow engine to cool down before proceeding with bumper installation. STEP 1: (SEE FIGURE 1) • Slide the ends of the latch into the slots located on the bottom of the bumper. Push the front of the latch down past plastic shroud of bumper. Latch will be under the shroud and should appear as shown in figure 3 when assembled correctly'. Attach one spring onto the rod on each side of the latch. LATCH _SPRING FIGURE 1 STEP 2: (SEE FIGURE 2) * insert 1/4 x 1-1/4" hex bolt through one of the springs. * Assemble 1/4 x 1-1/4" hex bolt onto the bumper using two 1/4-20 hex nuts (SIMS) with end of bolt extending slightly through outside nut. * Repeat for spring on other side. 1/4" HEX NUT (SIMS) 114 X 1-114" HEX BOLT SPRING FIGURE 2 STEP 3: (SEE FIGURE 3) Assemble a 3/8 x 1" hex bolt, 3/8" washer, frame brace and 3/8" lock nut to the rear hole of the bumper. 318 X 1" HEX BOLT 318" WASHER / \ / 318" LOCK NUT FRAME BRACE FIGURE 3 4 Call 1-866-576-8388 for missing parts or assembly help DO NOT RETURN TO STORE STEP 4: (SEE FIGURE 4) STEP 5: (SEE FIGURE 5) * Assemble a shoulder bolt, large washer and 3/8" lock * Fasten the frame braces to the tractor frame using nut to the frame brace and slotted hole on each side four 3/8-16 x 1" carriage bolts and 3/8" whizlock nuts. of the bumper. NOTE: Only tractor frame shown for clarity. 3/8" LOCK NUT \ 3/8-16 x 1" CARRIAGE BOLT "_ \ SHOULDER BOLT LARGE WASHER s FIGURE 4 3/8" WHIZLOCK LJ NUT TRACTOR / FRAME ._ FIGURE 5 TiLT BUMPER DOWN BEFORE TRACTOR HOOD: (SEE FIGURE RAiSiNG 6) * * While pushing in lightly on top of bumper, pull latch under front of bumper. Keep latch pulled out and pull down on bumper. LOCK BUMPER iNTO UP POSiTiON: (SEE FIGURE 6) * Push bumper up into position. Latch will lock bumper into place. \ LATCH © FIGURE 6 Call 1-866-576-8388 for missing parts or assembly help DO NOT RETURN TO STORE MODEL #486.24628 BRUSH GUARD 14 \ 16 15 \ 6 I 12 7 16 \ lo\ \ s 11 9 10 4 13 I 3 12 4 15 s \ 5 \ 5 6 Call 1-866-576-8388 for missing parts or assembly help DO NOT RETURN TO STORE MODEL #486.24628 BRUSH GUARD REF QTY PART NO. 1 421265 1 66696 2 26729 4 43350 4 44072 2 43001 2 43070 2 48106 2 R19171616 DESCRIPTION Brush Guard Assembly Latch Frame Brace Carriage Bolt, 3/8-16 x...