Stimmen - 1, Durchschnittliche Bewertung: 5
(
)
)
|
Anleitung Zusammenfassung
Some adjustments must be made periodically to properly maintain your Edger. All adjustments in the Service and Adjustments section of this manual must be checked at least once each season. ENGINE MAINTENANCE Use the following maintenance section to keep your unit in good operating condition. All the maintenance information for the engine is in the “Engine Instruction Book”. Before you start the engine, read this book. LUBRICATION 1. After each 25 hours, apply a small amount of engine oil to all moving parts, particularly the wheels. 2. To lubricate the engine, refer to the “Engine Instruction Book”. F–041105C 14 Note Direction Of Twist Note Direction Of Twist SERVICE AND ADJUSTMENT HOW TO REMOVE THE BELT The belt made of a special compound. If the belt becomes worn or breaks, replace the belt with an original equipment belt. 1. Disconnect the spark plug wire from the spark plug. 2. Drain the gasoline and oil from the engine. 3. Tip the Edger backwards on the handle. Block the top of the handle against a wall or under a bench. 4. Remove the screws from the belt guard (see Figure 11). Screw Belt Guard Belt Screw Figure 11 5. To compress the spring and release tension on the belt, push the blade bearing housing back toward the engine (see Figure 12). 6. Carefully note the twist of the belt around the engine pulley. Remove the old belt. Replace with an original equipment belt. 7. To install a new belt, reverse the above steps. Make sure to twist the new belt as shown in Figure 12. NOTE: If the belt is not installed properly, the blade will not turn in the proper direction and can damage the blade or belt. Engine Pulley Blade Housing Bearing Spring Figure 12 F–041105C 15 SERVICE AND ADJUSTMENT HOW TO REPLACE THE BLADE The blade is subject to wear and damage, such as nicks and dents. This will not generally affect its function. The blade is designed to not require sharpening. Do not attempt to sharpen the blade. The blade is also reversible. If nicks or dents are excessive, remove the blade and turn it around. This will provide a fresh cutting edge. Replace the blade if both sides are worn or damaged. WARNING: Do not sharpen the blade. Sharpening can damage the blade and cause it to break, which can cause injury to yourself or to others. To replace the blade, follow the steps below. 1. Disconnect the spark plug wire from the spark plug. 2. Remove the blade locknut that holds the blade to the drive shaft. WARNING: To remove or tighten the blade locknut, always use the method shown in Figure 13. Always position the holding wrench on the nut behind the blade. 3. Remove the blade. 4. Install a new blade and blade locknut. Tighten the blade locknut to a torque of 40–45 foot pounds. Turn Wrench To Tighten Locknut Blade Locknut Hold Nut, Do Not Turn Figure 13 F–041105C 16 SERVICE AND ADJUSTMENT STORAGE WARNING: Never store the Edger indoors with fuel in the fuel tank. Never store in an enclosed, poorly ventilated area where fumes could reach an open flame, a spark or a pilot light as on a furnace, water heater or clothes dryer. WARNING: Do not remove gasoline while inside a building, near a fire, or while you smoke. Gasoline fumes can cause an explosion or a fire. When the Edger is put in storage for thirty days or more, follow the steps below to make sure the Edger is in good condition the following season. 1. Drain the fuel tank. 2. Let the engine run until it is out of gasoline. 3. Drain the oil from the warm engine. Fill the engine crankcase with new oil. 4. Remove the spark plug from the cylinder. Pour one ounce of oil into the cylinder. Slowly pull the recoil–start grip so that the oil will protect the cylinder. Install a new spark plug in the cylinder. 5. Clean the dirt and debris from the cylinder cooling fins and the engine housing. 6. Completely clean the Edger. 7. Check the Edger for worn or damaged parts. Tighten all loose hardware. 8. Apply a small amount of engine oil to all moving parts, particularly the wheels. 9. Put the unit in a building that has good ventilation. 10. Cover the Edger with a suitable protective cover that does not retain moisture. Do not use plastic. IMPORTANT: Never cover the Edger while the engine and exhaust areas are still warm. NOTE: A yearly checkup or tune–up by an Authorized Service Center is a good way to make sure that your Edger will provide maximum performance for the next season. F–041105C 17 TROUBLE SHOOTING CHART TROUBLE CAUSE CORRECTION Engine difficult to start Stale fuel Drain fuel tank. Fill with fresh fuel. or Clogged fuel filter Replace fuel filter Engine runs erratically Engine runs erraticallyEngine runs erratically or oror Dirt in fuel tank or out of fuel Clean fuel tank. Carburetor out of adjustment See Carburetor Adjustment section. Engine will not run at fullEngine will not run at full speed Fouled spark plug Clean and set spark plug gap. Dirty air filter Replace air filter. Engine smokes excessively Plugged air filter Replace air filter. Debris interfering w...