Stimmen - 3, Durchschnittliche Bewertung: 4.3 ( )

Hersteller: MTD Dateigröße: 1.08 mb Dateiname: Unterrichtssprache:

See figure 3. 3. Line up holes in handle with holes in frame. See figure 3. 4- Secure rear wheels (P) and lower handle (M) to frame with shoulder bolts (A), belleville washers (B) (cupped side of washer against the frame), lock washers (C) and hex nuts (D). See figure 3. FRONT WHEEL BELLEVILLE WASHER (B) LOCK WASHER (C) HEX NUT. (D) Assemble the front wheel (0) as shown in figure 4. Place shoulder bolt (A) through wheel, then belleville washer (B) (between wheel and frame, cupped side against the frame). Secure with lock washer (C) and hex nut (D). See figure 4. FIGURE 4. FIGURE 5. 6. Assemble the upper handle (R) to lower handle. Place the head of carriage bolts (E)to the outside of handle. Secure with lock washers (F) and and hex nuts (G). See figure 5. 5 I 7. Place clutch plate (X) on the left hand side of the upper handle as shown in figure 6. Secure in place with hex bolts (H) and hex lock nuts (I). GRIP (N) FIGURE 7 8. Place hex bolt (J) through bottom hole in clutch handle as shown in figure 7, then through hole in adjustment bracket. 9. Secure hex bolt with compression spring (K), fiat washer (L) and hex lock nut (M) on the inside of the adjustment bracket. 10. Place compression spring (0) over straight end of clutch rod (U). Place end of rod in spindle bracket assembly and secure with cotter pin (P). See figure 8. 11. Secure bent end of clutch rod to clutch handle with cotter pin (P). See figure 7. 12. Slip the handle grip (N) on the end of the clutch handle. It will slip on more easily if it is first soaked in warm, soapy water. 6 OPERATION 1. Fill the crankcase with oil using a high quality detergent oil classified "For Service MS". Use SAE 30 oil. Nothing should be added to the recommended oil. Place the engine level. Remove oil fill cap. FILL THEOILSUMPTO POINT OF OVERFLOW. Pour slowly. See figure 9. Fill the fuel tank with clean, fresh, lead-free, low-lead or regular grade leaded gasoline. DO NOT MIX OIL WITH GASOLINE. 3. Pull the choke control out to "choke" position if necessary. See figure 10. FIGURE 10 . Grasp the starter handle and pull out the cord rapidly. Return it slowly to the engine. 5. After engine starts, push choke control in gradually. A CAUTION Rotating cutting blade may throw objects causing personal injury. Always wear safety glasses or some other suitable eye protection at all times the engine is running. Keep area clear of bystanders and do not operate without guards in place. To stop the edger engine, push the grounding clip against the spark plug. See figure 11. Depth Control Adjustment - The clutch handle controls the clutching and declutching of the belt. To declutch, the handle is pulled back toward the operator. To move the clutch handle, first move it to the left so the handle is out of the notch. ADJUSTMENTS AC WARNING | Disconnect the spark plug wire and ground against the engine before performing any adjustments, repairs or maintenance. Front Wheel Adjustment The front wheel may be raised or lowered to give added cutting depth. Loosen the second bolt on the front wheel support bracket. Pivot the bracket up or down to desired height. Retighten bolt. See figure 12. 7 SECOND BOLT WHEEL SUPPORT BRACKET FIGURE 12 LUBRICATION Engine - Refer to separate engine manual for lubrication instructions. Wheels - The wheels require no lubrication. Spindle Bearing - The ball bearing in the spine le is lubricated and sealed at the factory and requires no lubrication. Lubricate all other moving parts with engine oil. MAINTENANCE A WARNING Disconnect the spark plug wire and ground against the engine before performing any adjustments, repairs or maintenance. Blade Removal - Hold head of spindle bolt with a 3/4" or adjustable wrench and remove spindle nut. See figure 13. Engine Oil - Check oil level before starting er gine and after every 5 hours of operation. Add oil as necessary to keep level full to point of overflov/ing. Before removing plug, clean area around plug to prevent dirt from entering oil fill opening. Change oil after first 5 hours of operation. Thereafter, change every 25 hours. Change oil while er gine is warm. Oil may be drained thru oil drain plug. See figure 9. Crankcase capacity - 1 1/4 pints. FIGURE 13 Belt Removal - Remove the spark plug wire and ground. Remove the gasoline. 1. Tip the edger back so that it rests on the handle. 2. Remove the cotter pin securing the castle nut on the bottom of belt cover. See figure 14. FIGURE 14 3. Lift off the hex castle nut, belleville washer and belt cover. See figure 15. 4. Remove the old belt and replace with new belt. NOTE While the belt cover is removed, it is a good idea to apply a little grease to the pivot point on belt cover. See figure 15. 5. Reassemble the belt cover, making sure the new~ belt is over the engine pulley. 6. When tightening the castle nut, only tighten enough to line up hole in bolt for cotter pin. DO NOT OVER TIGHTEN. Belt cover mus...

Herunterladen

Geben Sie zwei Ziffern: