Stimmen - 4, Durchschnittliche Bewertung: 4.3 ( )

Hersteller: Flymo Dateigröße: 9.4 mb Dateiname: Unterrichtssprache:

9. Never cut grass by pulling the product towards you. 10. Switch off before pushing the mower oversurfaces other than grass. 11. Never operate the product with damaged guardsor without guards in place. 12. Keep hands and feet away from the blade at alltimes and especially when switching on themotor. 13. Do not tilt product when the motor is running, except when starting and stopping. In this case, do not tilt more than absolutely necessary andlift only the part which is away from the operator. Always ensure that both hands are in theoperating position before returning the productto the ground. 14. Do not put hands near the grass dischargechute. 15. Never pick up or carry a product when it isoperating or still connected to the mains supply. 16. Remove the plug from the mains : -before leaving the product unattended for anyperiod; -before clearing a blockage; -before checking, cleaning or working on theappliance; -if you hit an object. Do not use your productuntil you are sure that the entire product is in asafe operating condition.; -if the product starts to vibrate abnormally. Check immediately. Excessive vibration can cause injury. Maintenance and storage1. Caution: Do not touch rotating blade(s) 2. Keep all nuts, bolts and screws tight to be surethe lawnmower is in safe working condition. 3. Check the grassbox frequently for wear ordeterioration. 4. Replace worn or damaged parts for safety. 5. Only use the replacement blade, and blade boltspecified for this product. 6. Be careful during adjustment of the product toprevent entrapment of the fingers betweenmoving blades and fixed parts of the machine. 7. Store in a cool dry place and out of reach of children. Do not store outdoors. 8. Allow the product to cool for at least 30 minutesbefore storing. PAGE 3 CABLES - IMPORTANT • Use only 1.00mm2 size cable up to 40 metres length maximum. Maximum rating : 1.00mm2 size cable, 10 amps 250 volts AC. • YOUR PRODUCT IS SUPPLIED WITH AN ELECTRIC MAINS CABLE FITTED WITH A FEMALE CONNECTOR. 1. Flymo Mains Cables and Extension Cables are available from your local Approved Service Centre. 2. Do not wire an extension cable directly to your product yourself. Please contact your local Approved Service Centre for further information on the connectors and kits available. 3. Only use extension cables specifically designed for outdoor use. CONNECTORS - IMPORTANT • Flymo connectors are suitable for use with 2 core cable only. Under no circumstances should these connectors be used for earthed products. • All Flymo connectors and cables are of splashproof construction. They are not waterproof and must not be left outside permanently nor should they be submerged or immersed in water. Do not let cable lay or trail through pools of water or splashed with water from hose pipes. MAINS PLUG REPLACEMENT - IMPORTANT • If the plug supplied is cut off it should be destroyed. There is an electric shock hazard if a cut off plug is inserted into a 13 amp socket. 1. No earth required. Flymo products are double insulated to EN60335 and under no circumstances should an earth be connected to any part of the product. 2. Ensure the mains voltage suits your product 3. IMPORTANT! The wires in the mains lead are coloured in accordance with the following code: BLUE - NEUTRAL BROWN - LIVE The wire which is coloured BLUE must be connected to the Terminal which is marked with the letter 'N' or coloured BLACK. The wire which is coloured BROWN must be connected to the Terminal which is marked with the letter 'L' or coloured RED. 4. It is important that the outer sheath is clamped correctly into the 3-pin plug. 5. If in doubt consult your local Service Repairer or qualified electrician before the machine is used. 6. A 13 Amp fuse must be fitted to the Mains Plug. 7. The normal plug fuse and household fuse only protect the electrical equipment and are not a safeguard against electrocution. Cables IMPORTANT INFORMATION When received from the Manufacturer, the wheels are in a raised position. Do not switch on the product before removing from the raised position into position 5. A Roller Assembly B1 1. Turn product over. 2. Place both halves of the roller over the location pegs as illustrated in fig.B1 3. Clip the roller together to secure it into position.(B2) • Do not clip the roller together before placing over the location pegs B2 PAGE 4 D6 D7 D8 7. Ensuring the raised markings on the Pivot Block and the deck are aligned (D5), fold down the Cam Lock towards the Handle as illustrated in fig D6, and continue to turn clockwise (D7) until tightened. Repeat for the other side. 8. The Cam Lock can be unlocked and locked as illustrated in fig D8. D5 PAGE 5 4. Insert the Barrel Nut into the Cam Lock as illustrated in fig D1. 5. Ensuring the lower handle is in the correct position (D2) Insert the Lower Handle, Washer and Cam Lock on to the Bolt (D3) and turn the Cam Lock 3 times clockwise, as illustrated in fig D4. Assembly of Lower Handles to Lawnmower C1 C2 C3 1. P...

Herunterladen

Geben Sie zwei Ziffern: