Stimmen - 3, Durchschnittliche Bewertung: 4.3 ( )

Hersteller: Flymo Dateigröße: 2.13 mb Dateiname: Unterrichtssprache:

Do not wire an extension cable directly to your product The wire which is coloured BLUE must be connected yourself. Please contact your local Approved Serviceto the Terminal which is marked with the letter 'N' or Centre for further information on the connectors and coloured BLACK. kits available. The wire which is coloured BROWN must be con3. Only use extension cables specifically designed fornected to the Terminal which is marked with the letter outdoor use. 'L' or coloured RED. CONNECTORS - IMPORTANT 4. It is important that the outer sheath is clamped cor • Flymo connectors are suitable for use with 2 corerectly into the 3-pin plug. cable only. Under no circumstances should these con-5. If in doubt consult your local Service Repairer or qualinectors be used for earthed products. fied electrician before the machine is used. • All Flymo connectors and cables are of splashproof con-6. A 13 Amp fuse must be fitted to the Mains Plug. struction. They are not waterproof and must not be left7. The normal plug fuse and household fuse only protectoutside permanently nor should they be submerged or im-the electrical equipment and are not a safeguardmersed in water. Do not let cable lay or trail through poolsagainst electrocution. of water or splashed with water from hose pipes. MAINS PLUG REPLACEMENT - IMPORTANT If your product is hard wired i.e. non-detachable mains • If the plug supplied is cut off it should be destroyed. Thereelectric cable, a conversion kit and extension cable is is an electric shock hazard if a cut off plug is inserted intoavailable from all Approved Service Centres which a 13 amp socket. can be found in your local Yellow Pages. A • The Loose Parts Pack is packaged underneath the deck. Assembly of Lower Handles to Deck 1. Place the bolt (A2) through the hole in the lower handle (A1) until the lower handle fits into the recess (A3) 2. Place the washer (B1) and the wing knob (B2) on to the bolt and tighten the wing knob. 3. Repeat on the other side. Assembly of Upper Handles to Lower Handles. 1. Ensure the upper handle is located correctly with the lock-off button on the switchbox uppermost. 2. Ensure the upper handle (C1) and the lower handle (C2) are aligned correctly. 4. Fit the bolts (C3), washers (C4) and wing knobs (C5). Tighten the wing knob. 5. Fit the cable to the handles with the clips provided. Make sure the cable is not trapped between the upper and lower handles. Grassbox Assembly 1. Slide the grassbox tongue into the slots in the grassbox lower until it clicks securely into position (D) 2. Push the grassbox handle into the slots in the grassbox upper until it clicks securely into position. (E) 3. Starting at the rear of the grassbox, locate the grassbox upper into the grassbox lower by aligning the clips (F1). Ensure all clips are correctly located.(F2) before clicking into position. 4. Clip the two halves together, ensuring all clips are securely connected. Assembly Instructions B C D 1 E F1 F2 2 3 1 2 1 2 3 4 5 Grassbox J Fitting Fully Assembled Grassbox to Lawnmower. 1. Lift safety flap (G1) 2. Make sure the discharge chute is clean and free from debris (G2) 3. Locate fully assembled grassbox onto 2 location points (G3) at the rear of the deck as illustrated in pic. H 4. Locate safety flap onto the top of the grassbox. Ensure the grassbox is securely located. • IMPORTANT ! AFTER FITTING ENSURE NO GAP REMAINS BETWEEN THE SAFETY FLAP AND THE GRASSBOX. • Removal is the reverse procedure. • For larger areas of grass where grass collection is not required you can use your lawnmower without the grassbox. Ensure the Safety Flap is fully closed. The design of the safety flap permits the cut grass to be discharged downward behind the machine. Grassbox Full Window (Visimo Only) • As the grassbox fills up, grass will be visible through the window (J). • When the window/grassbox is full it is time to empty the grassbox. grassbox empty grassbox full G 1 2 3 H Visimo Only Cutting Height Adjustment Cutting Height Adjustment (K) & (L) • Height of cut is adjusted by raising or lowering the Front and Rear Wheels. • There are five heights of cut on this product. • NOTE A medium height of cut is recommended for most lawns. The quality of your lawn will suffer and collection will be poor if you cut too low. HEIGHT OF CUT WHEELS POSITION Low Front position 2cm Rear position 2cm Low to Medium Front position 2cm Rear position 4cm Medium Front position 4cm Rear position 4cm Medium to High Front position 4cm Rear position 6cm High Front position 6cm Rear position 6cm K L 2cm 6cm 4cm Removing and Fitting the Blade Switch off, wait until the blade has stopped rotating and disconnect from the mains electricity supply BEFORE attempting to remove or refit the blade. Always handle the blade with care - sharp edges could cause injury. USE GLOVES. Removing the Blade 1. To remove the blade bolt, hold the blade firmly with a gloved hand and with a spanner, loosen the blade bolt by turning it anti-clockwise (S). 2. ...

Herunterladen

Geben Sie zwei Ziffern: