Stimmen - , Durchschnittliche Bewertung: ( )

Anleitung Husqvarna, modell Trailer 275

Hersteller: Husqvarna
Dateigröße: 1.18 mb
Dateiname:

Unterrichtssprache:

Das Dokument wird geladen, bitte warten

HerunterladenSchließen

Das Dokument wird geladen, bitte warten

HerunterladenSchließen

int. 4 C Capsule de moyeu 2 D Vis à tête hexagonale de 1/4x 1/2" (6x12 mm) 23 E Vis à tête hexagonale de 1/4x5/8" (6x16 mm) 6 F Vis à tête hexagonale de 1/4x3/4" (6x20 mm) 6 G Visàtêtehexagonalede1/4x1-1/2"(6x40mm) 2 H Rondelle de blocage de 1/4" (6 mm) de diam. int. 37 I Ecrou de 1 /4" (6 mm) 37 J Vis à tête fendue de 5/16x3/4" (8x20 mm) 14 K Rondelle de blocage de 5/16" de diam. int. 14 L Ecrou de 5/16" (8 mm) 14 M Vis à tête hexagonale de 3/8" x1" (10x25 mm) 2 N Rondelle de blocage de 3/8" (10 mm) de diam. int. 2 O Ecrou de 3/8" (10 mm) 2 Fig. 1 Liste d’identification : Pièces détachées (voir la figure 2) P Côté droit de la remorque Q Pince arrière R Côté gauche de la remorque S Fixation de la trappe arrière T Coin U Tige avant V Tige de traction X Suspension de la roue Y Moyeu de roue Z Renforcement de trappe arrière AA Support de serrage BB Verrouillage au plancher, partiellement monté CC Fixation detraction DD Roue Fig. 2 7 Montageset Trailer 275 De montageset bevat de volgende onderdelen: Aantal A Borgpen 1 /8 x 1" (3 x 25 mm) 2 B Ring 25/32, I.D. (20 mm) 4 C Naafdop 2 D Zeskante bout 1 /4 x 1 /2" (6 x 12 m m) 23 E Zeskante bout 1 /4 x 5/8" (6 x 16 m m) 6 F Zeskante bout 1 /4x 3/4" (6 x 20 mm) 6 G Zeskante bout 1 /4 x 11 /2" (6 x 40 mm) 2 H Borgring 1/4" I.D. (6 mm) 37 I Moer1/4"(6mm) 37 J Schroef 5/16 x 3/4" (8 x 20 mm) 14 K Borgring 5/16 I.D. 14 L Moer5/16"(8mm) 14 M Zeskante bout 3/8 x 1" (10 x 25 mm) 2 N Borgring 3/8" I.D. (10 mm) 2 0 Moer3/8"(10mm) 2 Fig. 1 Lijst voor het herkennen van de onderdelen: Losse onderdelen (zie fig. 2) P Rechterzijde van de wagen Q Achterklep R Linkerzijde van de wagen S Bevestiging van de achterklep T Hoek U Voorklep van de wagen V Trekstang X Wielophanging Y Wielas Z Verksterking van achterklep AA Steun van vergrendeling BB Vergrendeling van de bak CC T rekbevestiging DD Wiel Fig. 2 © Assembly instructions 1. Remove the hardware pack and all loose parts from the carton. Be sure carton is empty before discarding. 2. Lay out all the parts as shown in figure 2. 3. Position cart body halves (P and R) upright as shown in figure 3. N.B. Large diameter holes to the top. 4. Start bolts (D), lock washers (H) and hex nuts (I) through flanges, only make finger tight until all 7 bolts are in place. See figure 3 and note below. N.B. Bolts are tightened later in step 11, page 10. 5. Position the wheel support (X) in place on the bottom of cart. See figure 4. 6. Assemble wheel support to cart with eight slotted head screws (J), lock washers (K) and hex nuts (L). See figure 4. Heads of screws go to the inside of cart and should be tightened at this time. 7. Position the tailgate reinforcement bracket (Z) over end of cart. See figure 5. 8. Start slotted screws (J) through bottom of cart (heads of screws to the inside of cart) and reinforcement bracket. Secure finger tight with hex nuts (L) and lock washers (K). See figure 5. 9. Position the tailgate ...