Stimmen - , Durchschnittliche Bewertung: ( )

Anleitung Husqvarna, modell 966043502

Hersteller: Husqvarna
Dateigröße: 2.12 mb
Dateiname:

Unterrichtssprache:

Das Dokument wird geladen, bitte warten

HerunterladenSchließen

Das Dokument wird geladen, bitte warten

HerunterladenSchließen

These settings are approximate and may vary due to physical characteristics of the product. Walking speed. wear, condition of the turf and humidity, may cause actual rate setting to deviate. No expressed nor implied warranty or guarantee is provided as to coverage or uniformity indicated by these rate settings. 70 LP Setting 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 PrizelawnPrizelawnPrizelawnPrizelawnBF-1 /SS,HVO, CBRlll, Setting G H J K M N N1/2 O P1/2 Q R S T U V X Z Lesco Hi-WHEEL Setting E F G H I J K L — — M N O — P R S Scott Speedy Green Setting — — 2 — 3 — 4 — 5 — 6 — 7 — 8 — — Scotts R8A/SR-1, AP&SR2000 Setting I J L M O P — Q — S T U — V W X Z FERTILIZER PARTICLE SIZE BAG RATE Pounds of fertilizer used per 1,000 sq. ft. of coverage APPROX. SETTING APPROX. SPREAD WIDTH Large, heavy particles 5 10 15 6 9 11 12 FT. 12 FT. 12 FT. Medium-mixed particles 5 10 15 5 7 9 10 FT. 10 FT. 10 FT. Small particles (nitrogen) 1 2 3 2 4 5 10 FT. 10 FT. 10 FT. Mixed size particles -some fines 5 10 15 6 9 11 8 FT. 8 FT. 8 FT. Light weight particles 5 10 15 4 5 6 6 FT. To 8 FT. The following provides approximate The following provides approximate 70 LP settings when only the product weight, square 6 70 LPsettings for those units listed. foot coverage, and visual inspection of the material is available. RATESETTINGCONVERSIONRATESETTINGCONVERSIONRATESETTINGCONVERSIONRATESETTINGCONVERSIONThe conversions should be used as guidelines for establishing proper rate settings for the particular product being applied. Steps for obtaining the most accurate settings are outlined in the “How to Determine Spreader Settings and Spread Width” section of this manual. These settings are approximate and may vary due to physical characteristics of the product. Walking speed. wear, condition of the turf and humidity, may cause actual rate setting to deviate. No expressed nor implied warranty or guarantee is provided as to coverage or uniformity indicated by these rate settings. 70 LP Setting 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 PrizelawnPrizelawnPrizelawnPrizelawnBF-1 /SS,HVO, CBRlll, Setting G H J K M N N1/2 O P1/2 Q R S T U V X Z Lesco Hi-WHEEL Setting E F G H I J K L — — M N O — P R S Scott Speedy Green Setting — — 2 — 3 — 4 — 5 — 6 — 7 — 8 — — Scotts R8A/SR-1, AP&SR2000 Setting I J L M O P — Q — S T U — V W X Z FERTILIZER PARTICLE SIZE BAG RATE Pounds of fertilizer used per 1,000 sq. ft. of coverage APPROX. SETTING APPROX. SPREAD WIDTH Large, heavy particles 5 10 15 6 9 11 12 FT. 12 FT. 12 FT. Medium-mixed particles 5 10 15 5 7 9 10 FT. 10 FT. 10 FT. Small particles (nitrogen) 1 2 3 2 4 5 10 FT. 10 FT. 10 FT. Mixed size particles -some fines 5 10 15 6 9 11 8 FT. 8 FT. 8 FT. Light weight particles 5 10 15 4 5 6 6 FT. To 8 FT. The following provides approximate The following provides approximate 70 LP settings when only the product weight, square 6 70 LPsettings for those units listed. foot coverage, and visual inspection of the material is available. Oil Oil Oil Oil MAINTENANCEMAINTENANCEMAINTENANCEMAINTENANCE 1. Never store unused material in spreader. Return unused product to its original container. 2. Open and wash spreader thoroughly after each use and dry completely in sun or heated area. 3. Oil the axle bearings, impeller shaft bearing in hopper. 4. Remove gear cover and wash gears thoroughly. Oil all bearing areas and face of gear teeth. Reinstall gear cover. 5. Gear mesh should be checked on a regular basis during high use periods. Clearance between the axle gear and pinion gear should be minimal but not tight. If adjustment is necessary, loosen axle collar set screw and hold gears together. Slide axle collar against the gear support and tighten axle collar set screw. Spin drive wheel. Gears should run freely and smoothly. 6. Impeller surface should be cleaned periodically to remove build-up of product. Build-up can cause the spread pattern to change. 7. Tire pressure should be 20-25 PSI. Oil Impeller Shaft Bearing In Hopper Axle Collar Oil NOTESNOTESNOTESNOTES 7 1. SPREADER MODEL NUMBER 2. SPREADER NAME 3. PART NUMBER 4. NAME OF PART AS SHOWN PartsListModelPartsListModelPartsListModelPartsListModel70LP70LP70LP70LP1 1A 4 2 3 5 6 11 10 12 18 8 13 7 19 20 21 7 22 2324 25 26 27 28 9 30 Ke y Description Part No. Key No. Description Part No. 1 Hopper Assembly 525 56 82-06 17 Impeller Shaft 525 56 87-06 1A Hopper * 525 56 82-07 18 Screen Clip (2 Req.) 525 56 91-02 2 Shutoff Plate * 525 56 84-03 19 Hopper Screen 525 56 82-08 3 Shutoff Plate Guides (Set)* 525 56 84-04 20 Hopper Label * 525 56 82-08 4 Rate Cam & Chute Assembly * 525 56 83-03 21 Handle Brace W/ Plug– LH. 525 56 85-05 5 Impeller Assembly 525 56 87-05 22 Agitator 525 57 00-01 6 Frame Assembly 525 556 92-02 23 Upper Handle Assembly 525 56 85-07 7 Drive & Free Turning Wheel 525 56 96-02 24 Handle Grip (2 Req.) 525 56 85-08 8 Axle Collar 525 56 86-06 25 On/Off Control 525 56 93-02 9 Axle Gear 525 56 86-05 26 Cable Clamp 525 56 90-01 10 Gear Cover Assembly (2 Req.) 525 5...