Stimmen - 3, Durchschnittliche Bewertung: 5 ( )

Hersteller: Poulan Dateigröße: 657.96 kb Dateiname: Unterrichtssprache:

ALIGNMENT MARKS 02085 COVER SEAL FIG. 3 7 SUPPORT POST (See Fig. 4) Use Hardware - - GROUP "C" CAUTION: Container sup port is spring loaded and locked to the cover. Handle cover assembly carefully so as not to unlatch the cover from the container support. 1. Rotate cover assembly onto its side as shown. 2. Assemble support post to container support with the three (3) carriage bolts and locknuts. Tighten securely. 02091 LOCKNUTS CARRIAGE BOLTS SUPPORT POST FIG. 4 5 5 MOUNTING TO TRACTOR (See Fig. 5) Use Hardware - - GROUP "D" NOTE: For ease of assembly, you may wish to obtain the as sis tance of another person for mounting assembly to tractor. 1. Raise seat on tractor to allow assembly to be mounted. 2. With cover closed, lift assembly and place support post inside mounting bracket. Allow assembly to rest on lanced tabs of mounting bracket. 3. Line up holes in mounting bracket with holes in support post and insert bracket support pin. Secure with retainer spring. 4. Unlatch and open cover. 5. Install the three (3) tubing end caps onto container support. 6. Tap each end cap onto container support tubes to seat securely. BRACKET COVER ASSEMBLY SUPPORT PIN 02096 FIG. 5 END CAP SUPPORT POST MOUNTING BRACKET LANCED TABS RETAINER SPRING 8 9 WARNING Donotoperatemowerunlesscontainerisproperlyis subjecttowearanddetierioration.Checkbagfrequently.Replacewhen crackedordamaged.Useonlyarecommendedreplacementcontainer. WARNING 02082 02343 CONTAINER MOUNTING (See Fig. 7) No hardware required 1. Install one container to left side fi rst with warning to outside of unit. Install other container to right side. NOTE: Right con tain er should always over lap left con tain er at center sup port. 2. Close cover and lock latch handle over center support tube. 7 COVER LATCH HANDLE CENTER SUPPORT TUBE CONTAINER WARNING CONTAINER HANDLE FIG. 7 CONTAINER WARNING DEFLECTOR SHIELD MOWER DECK BAFFLE WASHER LOWER CHUTE (See Fig. 8) Use Hardware - - GROUP "E" 1. Raise and hold defl ector shield in upright position. 2. Slide back edge of chute over rear corner of mower deck and pivot forward. 3. Align slot in lower chute with hex bolt in mower deck baffl e and close chute over deck openning. 4. Secure with washer and wing nut. CAUTION: Do not remove discharge guard from mower. Raise and hold guard when attaching lower chute and allow it to rest on chute while in operation. WING NUT HEX BOLT FIG. 8 8 PRESS TOGETHER TO FORM SEAL WHILE LIFTING TOP HALF 02089 CONTAINER BOTTOM HALF CONTAINER TOP HALF ASSEMBLY CHECK: Squeeze sides of lower half of contain er and check that there is no gap between upper and lower halves. If a gap appears, unlock tabs to separate container halves and repeat instructions above. LOCKING TAB WARNING Donotoperatemowerunlesscontainerisprope rlyissubjecttowearanddetierioration.Checkbagfrequ ently.Replacewhencrackedordamaged.Use onlya recomme nded replacementcontainer. 02097 FIG. 6 02739 CONTAINER BOTTOM HALF CONTAINER TOP HALF CONTAINER ASSEMBLY (See Fig. 6) No hardware required 1. Place bottom half inside of top half, as shown. 2. Place one foot inside bottom half and lift top half to meet bottom half. 3. Press halves tightly together while lifting top to lock into place as shown. IMPORTANT: BEFORE LOCKING THE TABS, HOOKED EDGES ON BOTH HALVES MUST OVERLAP TO FORM SEAL AS SHOWN IN INSET. 4. Repeat for second container. 6 10 WARNING Donotoperatemowerunlesscontainerisproperlyisnstalled.Containeris subjecttowearanddetierioration.Checkbagfrequently.Replacewhen crackedordamaged.Useonlyarecommendedreplacementcontainer. WARNING Donotoperatemowerunlesscontainerisproperlyisnstalled.Containeris subjecttowearanddetierioration.Checkbagfrequently.Replacewhen crackedordamaged.Useonlyarecommendedreplacementcontainer. 02344 WARNING Donotoperatemowerunlesscontainerisproperlyisnstalled.Containeris subjecttowearanddetierioration.Checkbagfrequently.Replacewhen crackedordamaged.Useonlyarecommendedreplacementcontainer. WARNING Donotoperatemowerunlesscontainerisproperlyisnstalled.Containeris subjecttowearanddetierioration.Checkbagfrequently.Replacewhen crackedordamaged.Useonlyarecommendedreplacementcontainer. 02345 11 LEVEL MOWER DECK No hardware required Be sure deck is properly leveled for best mower per for man ce. See your tractors owner's manual for ins truc tions. 10 UPPER CHUTE (See Figs. 10A & 10B) No hardware required 1. Lower mower deck to its lowest cutting position. 2. Assemble upper chute by inserting curved end into hole in back of cover. NOTE: Handle carefully so as not to damage dump bag indicator. 3. Push in and turn upper chute until it is in line with lower chute. 4. Align the bosses on lower chute with alignment slots on upper chute and slide together. 5. Secure with rubber latch by hooking hole in latch over latch pin. LOWER CHUTE COVER DUMP BAG UPPER INDICATOR CHUTE HANDLE FIG. 10A RUBBER LATCH ALIGNMENT SLOTS BOSSES LATCH PIN FIG. 10B 02102 CHUTE LATCH ASSEMBLY (See Fig. 9) Use Hardware - - GROUPS "F & G" 1. Assemble latc...

Herunterladen

Geben Sie zwei Ziffern: