Stimmen - 2, Durchschnittliche Bewertung: 4.5 ( )

Hersteller: Poulan Dateigröße: 689.67 kb Dateiname: Unterrichtssprache:

Always wear safety glasses or eye shields be fore starting your trac tor and while mow ing. We recommend wide vision safety mask for over the spec tacles or stan dard safety glasses. UNPACKING INSTRUCTIONS • Remove all parts and packing materials from carton. • Foldflaps to inside of carton and turn carton upsidedown on floor of work area. To protect grass catcher cover during assembly place cover upsidedown on overturned carton. • Check carton contents against list. Be sure all parts are there. CARTON CONTENTS: (2) Container Tops (1) Mounting Bracket (2) Container Bottoms (1) Cover Assembly (1) Upper Chute (1) Cover Seal (1) Lower Chute (1) Bag of Parts (1) Support Post (1) Owner's Manual GROUP "A" ASSEMBLY LOCATION HARDWARE SHOWN ACTUAL SIZE BAG OF PARTS CONTENTS GROUP "B" GROUP "C" REAR MOUNTING BRACKET TO DRAW BAR (4) Shoulder Bolt 5/16 - 18 Self Tapping SUPPORT POST TO CONTAINER SUPPORT (3) Carriage Bolt 5/16 - 18 x 3/4 (3) Locknut 5/16-18 (4) Bolt 5/16 - 18 x 3/4 (4) Locknut 5/16-18 (1) Bracket Support Pin (1) Retainer Spring (3) Tubing End Caps SUPPORT POST TO MOUNTING BRACKET 4 BAG OF PARTS CONTENTS (continued) CHUTE LATCH ASSEMBLY TO UPPER CHUTE LOWER CHUTE ASSEMBLY TO MOWER DECK CHUTE LATCH ASSEMBLY TO LOWER CHUTE GROUP "E" GROUP "D" (1) Screw #10 x 1-1/8 (2) Washer 3/16 x 3/4 x 16 Ga. (1) Nut, Acorn #10 (1) Spacer, Split #10 (1) Rubber Latch GROUP "F " (2) Nut, Weld #10 (2) Washer, Lock #10 (2) Washer 3/16 x 3/4 x 16 Ga. (2) Screw #10 x 5/8 (2) Latch Hook Assembly (1) Nut, Weld #10 (1) Washer, Lock #10 (1) Washer 3/16 x 3/4 x 16 Ga. (1) Screw #10 x 5/8 5 PARTS IDENTIFICATION ASSEMBLY COVER ASSEMBLY GRASS CATCHER CONTAINERS LOWER CHUTE ATTACHING STRAPS WARNINGDonotoperatemowerunlesscontainerisproperlyissubjecttowearanddetierioration.Checkbagfrequently.Replacewhencrackedordamaged.Useonlyarecommendedreplacementcontainer. WARNINGlesscontainerDonotoperatemowerunisproperlyissubjecttowearanddetierioration.Checkbagfrequently.Replacewhencrackedordamaged.Useonlyarecommendedreplacementcontainer. 02084LOWER CHUTE CHUTE LATCH UPPER CHUTE DUMP BAG INDICATOR NOTE: When right hand (R.H.) and left hand (L.H.) are mentioned in this manual, it means when you are seated on the tractor, in the operator's position. (1) 3/8" Wrench (1) Drive Ratchet THESE ARE THE TOOLS YOU WILL NEED TO (1) 1/2" Wrench (1) 3" or longer Extension ASSEMBLE YOUR GRASS CATCHER: (2) 9/16" Wrenches (1) Short Handle(1) 1/2" Socket Phillips Screwdriver (1) 9/16" Deep well Socket CAUTION: BEFORE ASSEMBLING GRASS CATCHER TO TRACTOR: • Depress clutch/brake pedal fully and set parking brake. • Place gearshift/motion control lever in neutral (N) position. • Place attachment clutch in "DISENGAGED" position. • Turn ignition key "OFF" and remove key. • Make sure the blade and all moving parts have completely stopped. • Disconnect spark plug wire from spark plug and place wire where it cannot come in contact with plug. 6 7 02091 02085 SUPPORT POST (See Fig. 3) Use Hardware - - GROUP "B" CAUTION: Container support is spring loaded and locked to the cover. Handle cover assembly carefully so as not to unlatch the cover from the container support. 1. Rotate cover assembly onto its side as shown. 2. Assemble support post to container support with the three (3) carriage bolts and locknuts. Tighten securely. ALIGNMENT MARKS COVER SEAL FIG. 2 COVER SEAL (See Fig. 2) No hardware required 1. Align mark on seal with mark at cover opening. 2. Work seal into opening so cover sits between fl anges of seal. 2 3 REAR MOUNTING BRACKET (See Figs. 1A, 1B & 1C) NOTE: If your tractor already has four (4) shoulder bolts installed on the rear draw bar, simply hang the mounting bracket, lanced tabs towards bottom, on the bolts. Discard hardware group "A" and disregard the remaining Step 1 instructions. 1 If your tractor does not have four (4) shoulder bolts installed on the drawbar, follow the instructions below. Use Hardware - - GROUP "A" Only one set of hardware in GROUP "A" will be used to mount the rear mounting bracket. To determine which set is correct for your tractor, check to see if there are (2) two upper corner ribs on each side of drawbar. If your tractor has the upper corner ribs, use the (4) four self tapping shoulder bolts. If your tractor does not have the corner ribs, use the set of (4) four bolts and locknuts. SELF TAPPING SHOULDER BOLTS (See Fig. 1B) 1. Using the four formed holes in the drawbar, install the four shoulder bolts as shown and tighten securely. 2. Hang the mounting bracket, lanced tabs towards bottom, on the bolts. LOCKNUTS CARRIAGE BOLTS SUPPORT POST FIG. 3 LANCED TABS TOWARD BOTTOM 02337 SHOULDER BOLTS FIG. 1A 02336 UPPER CORNER RIBS UPPER CORNER RIBS SELF TAPPING SHOULDER BOLTS FIG. 1B LANCED TABS TOWARD BOTTOM BOLTS AND LOCKNUTS (See Fig. 1C) 1. Assemble the mounting bracket, lanced tabs towards bottom, using the four smaller inside holes on the drawbar. 2. Install the four bolts and locknuts as shown and tighten securely. 02335 FIG. 1C LAN...

Herunterladen

Geben Sie zwei Ziffern: