Stimmen - 2, Durchschnittliche Bewertung: 3.5 ( )

Hersteller: Dixon Dateigröße: 2.73 mb Dateiname: Unterrichtssprache:

In order to increase or decrease the engine speed, the control is moved forward or back respectively. Avoid idling the engine for long periods, as there is a risk of fouling the spark plugs. USE FULL THROTTLE WHEN MOWING, for best mower performance and battery charging. 12. Lifting Lever for the Mower Deck The lifting lever is used to place the mower deck in the transport position or one of the 17 different cutting height positions. The cutting height is set by placing a peg in the hole for the desired cutting height and the peg is then locked on the inside (hidden in the illustration) with the supplied pin. Pull the lever backward to the locked position to engage the transport position. The deck is then raised. Depress the lock handle, counter hold, and move the lifting lever forward toward the peg to engage the set cutting height. The deck is then lowered. The lifting lever can also be used to temporarily adjust the cutting height, such as when passing a minor bump in the lawn. IMPORTANT INFORMATION In order to obtain an even cutting height it is important that the air pressure in all four tires is the same 15 psi (1 bar). IMPORTANT INFORMATION Always use the high position to transport. Throttle control The mower deck’s lifting lever English-24 CONTROLS Pump release valves IMPORTANT INFORMATION Only rotate valve . - . turn to release system. Tighten the valve moderately. Do not overtighten the valve when closing. That can damage the valve seat. Pump release valves are located at the pumps. They are used to release the system so the machine may be moved by hand when not running. Tilt seat forward to gain access to the pumps. Use a 5/8" wrench to open both valves. Tracking 1. Tracking adjustment is done using the tracking bolts. The tracking bolts act as limiting devices for the motion control levers when in the full-forward position. 2. Start by loosening jam nut on right tracking bolt. Back the tracking bolt out until fl ush with nut. 3. Loosen left bolt and back out until fl ush with nut. 4. Move unit to an open, unobstructed area such as an empty parking lot or open fi eld for tracking adjustment. 5. Test operation of the unit by driving it at full throttle and full forward position on both motion control levers. Gradually turn in the tracking bolt on the right hand side until the unit noticeably starts drifting right. 6. Stop the unit and tighten right jam nut in this position. 7. Restart the unit and drive forward at full throttle with both motion control levers in full forward position. Gradually turn in the left bolt until unit tracks straight. Tighten jam nut. Pump release valve 6.05.54.51. Tracking bolt 1 Tracking adjustment Accessories For mulching, there is a BioClip attachment available. This is mounted underneath the mower deck and consists of control plates and BioClip blades. English-25 OPERATION Operation Read “Safety Instructions” section and following pages, if you are unfamiliar with the machine. Training Zero turn mowers are far more maneuverable than typical riding mowers due to their unique steering capabilities. We suggest that this section be reviewed in its entirety prior to attempting to move the mower under its own power. Additionally, we suggest when first operating the mower, use a reduced throttle speed and reduced ground speed by NOT moving control levers to the furthest forward or reverse positions during initial operation, or until operator becomes comfortable with controls. We also suggest first time users, or new users to Zero Turn mowers to become familiar with the mower’s movement on a hard surface, such as concrete or blacktop PRIOR to attempting to operate on turf. Until operator becomes comfortable with mower controls and zero turning capability, they may damage turf due to overly aggressive maneuvers. To move forward and backward The direction and speed of the mower’s movements is effected by the movement of the control lever(s) on each side of mower. The left control lever controls the left wheel. The right control lever controls the right wheel. IMPORTANT INFORMATION When control levers are in the reverse position they return to neutral when released. This may cause the mower to suddenly stop. First time users should push mower (see “Moving by Hand” in the “Operation” section) to an open, fl at area, without other people or vehicles/obstacles nearby. In order to move unit under its own power, the operator must be in the seat, start engine (see “Before Starting” in “Operation” section), adjust engine speed to idle, disengage parking brake, do not engage blades at this time, rotate control levers inward. As long as the control levers have not been moved forward or backwards, mower will not move. Slowly move both control levers forward slightly. This will allow mower to start moving forward in a straight line. Pull back on control levers to the neutral position and mower should stop moving. Pull back slightly on control levers, this will allow mower to start moving b...

Herunterladen

Geben Sie zwei Ziffern: