Stimmen - 2, Durchschnittliche Bewertung: 4.5 ( )

Hersteller: Bad Boy Mowers Dateigröße: 2.86 mb Dateiname: Unterrichtssprache:

x 3/4” LONG 55---- - A0585- - ......1 - - - - - UPPER FRAME ASSEMBLY KEY-WAY 5б---- -V1054-- ......1 - - - - - INLET BLOWER PULLEY 57---- - A0611 -- ......1 - - - - - ENGINE PULLEY WASHER 58---- - B0246 - - ......1 - - ---LOWER MOUNT TUBE 3/8”-1б x 3/4” HHCS 59---- - E6009- - ......1 - - ---8” BLOWER CONE BLACK HANDLE GRIP б0---- - J6011 -- ......2 -- - - - 5”-6” HOSE CLAMP PTO HANDLE ASSEMBLY б1---- - J6006 - - ......2 -- - - - 7”-8” HOSE CLAMP 1/4”-20 x 3/4” HHCS б2---- - A0584- - ......3 -- - - - BAG RING ASSEMBLY PTO HANDLE MOUNT б3---- - B0247- - ......1 - - ---LOWER MOUNT TUBE ASSEMBLY STIFFENER 1/4”-20 NYLOC NUT б4---- - HB0231 - ......1 -- - - - UNIT HARDWARE BAG HAIRPIN CLIP HB0234 - ......1 - - - - - ENGINE PULLEY 3/8”-1б SET SCREW HARDWARE BAG CAM BRACKETASSEMBLY HB0232 - ......1 - - - - - BOOT KIT HARDWARE BAG 5/1б”-18 FLANGE NUT HB0233 - ......1 - - - - - WEIGHT KIT HARDWARE 5/1б”-18 x 2” HHCS BAG PTO ARM ASSEMBLY бб---- ******* ......1 - - - - - 6” x 29” UPPER HOSE 3/8”-1б x 2-1/2” HHCS бб---- ******* ......1 - - - - - 8” x 34” LOWER HOSE 3/8”-1б FLANGE NUT б7---- - G0002- - ......3 - - - - - COLLECTION BAG 3/8”-1б x 1-1/2” HHCS б8---- - B2220- - ......1 - - ---WEIGHT BAR BELT GUIDE BRACKET б9---- -B0184-- ......1 - - - - - BOOT PLATE GEAR BOX ASSEMBLY 70---- - B0244 - - ......1 - - - - - BOOT ROD PULLEY GUARD 71---- - E1113 - - ......1 - - - - - BOOT 1/4”-20 x /” HHSTS 72---- - A0597- - ......1 - - - - - WEIGHT BRKT ASSEMBLY 10 2-7 Upper Frame Assembly Installation NOTE: During this step, it is suggested that two people install the upper frame to the lower mount tube. Using two people to lift the upper frame, lift the upper frame above the lower mount tube making sure the frame is pointing away from the mower (Figure 9). Slide the upper frame tube into the lower mount tube aligning the mounting hole. Insert (1) /” x 2-1/2” clevis pin P#(K0133) through the hole and fasten with (1) 5/32” x 2-5/8” hair pin clip P#(K0088). Figure 9. Fasten w/ (1)/”x 2-1/2” Clevis Pin (1) Hair Pin Clip m HI Lower Mount Tube Upper Frame 2-8 Top Assembly To Upper Frame Assembly Installation Align the pivot brackets of the top assembly P#(A0551) to the pivot point on either side of the upper frame assembly. Place (1) P#(K0041) fender washer between each pivot point (Figure 10) and fasten each side by using (1) P#(K1153) 5/16”-18 x 3/4” HHCS and (1) P#(K1180) 5/16”-18 nyloc nut. When fastening leave nut slightly loose so that the top can pivot freely. Figure 10. Top Assembly Here 2-9 Boot To Mower Deck Installation 60” Boot Plate Mounting Instructions To mount the boot plate P#(B0184) to the boot P#(E1113) use (2) 3/8”-16 x 1” carriage bolts P#(K1182) and (2) 3/8”-16 flange nuts P#(K1215). See Figure 11 for bolt placement. 48” & 52” Boot Plate Mounting Instructions To mount the boot plate P#(B0184) to the boot P#(E1113) use (2) 3/8”-16 x 1” carriage bolts P#(K1182) and (2) 3/8”-16 flange nuts P#(K1215). See Figure 12 for bolt placement. NOTE: When bolting the boot and boot plate together, the head of the bolt is placed from the inside of the boot. This will prevent grass from collecting on the bolts. For All Deck Sizes Remove the bolts that hold the deflector shield in place so that the boot rod can fasten the boot and boot plate to the mower deck. Align the holes in the boot plate to the holes in the deflector shield mount and slide the boot rod P#(B0244) through and fasten by using (1) hair pin clip P#(K0099). NOTE: The mower's deflector shield is removed in the following photo for clarity. Always have the deflector shield mounted when mowing. Figure 11 Fasten w/ Boot Rod Fasten w/ (1) 5/16” x 3/4” HHCS (1)5/16” Nyloc Nut (1) Fender Washer Per Side Fasten w/ (2) 3/8” x 1” Carriage Bolts (2) 3/8” Flange Nuts 11 Figure 12. lock bushing, forcing the blade to break-away from the taper-lock bushing. If the impeller will not move, hit the base of the impeller, between each vein, with a hammer, then try again. To Replace: Place impeller blade over the engine shaft. Slide the taper-lock bushing into the engine shaft and into the impeller blade, aligning the non-threaded holes of the taper-lock bushing to the threaded holes of the impeller blade. Fasten by using (2) 1/4”-20 x 1” HHCS Grade 8 (torque to 15 ft. lbs), (1) spacer washer and (1) 3/8”-16 x 1” HHCS Grade 8 w/washer. Figure 14. 2-10 Blower Cone Installation Thread (1) 5/16”-18 jam nut P#(K0120) onto each end of (2) 5/16”-18 x 2-1/2” HHCS P#(K0125). Now partially thread the bolts into each of the two tabs located on the blower housing. Place blower cone so the two tabs line up with the bolts then tighten completely. See Figure 13. Impeller Blade Figure 13. Blower Cone Blower Housing Tabs Fasten w/ (2) 5/16” x 2-1/2” HHCS (2) 5/16” Jam Nuts 2-11 Impeller Blade Removal/Replacement Taper-Lock Bushing To Remove: First remove the center 3/8” bolt and the (2) washers from the taper-lock bus...

Herunterladen

Geben Sie zwei Ziffern: