Stimmen - 5, Durchschnittliche Bewertung: 3.8 ( )

Hersteller: Bolens Dateigröße: 2.68 mb Dateiname: Unterrichtssprache:

After assembly, see operating section of this manual for proper fuel and engine oil recommendations. Your new mower is shipped preassembled with the exception of the handle and wheels. 1. Remove lawn mower and all parts from the carton. Make certain that all loose parts and literature have been removed before the carton is discarded. NOTE Throttle control may be optional on your unit. 2. Extend throttle control assembly which is attached to engine at the rear of the mower and place on floor. A CAUTION Do not bend or kink control wires. ■3. Place lower handle in line with hole on deck. Secure to deck with shoulder bolts (I), lock washers (J) and hex nuts (K). See figure 3. NOTE It may be necessary to bend the ends of the lower handle inward slightly to assure a snug fit against the deck mounting area. Your mower has four height settings. Use the same hole for all four wheels when assembling. See figure 4. Place shoulder bolt (F) through wheel. See figure 4. Place crown side of belleville washer towards the wheel (away from deck). See figure 4. Secure wheel to deck, using hex nut (H) and lock washer (G). FIGURE 4. 6 Upper Handle Halves .■ "V •£? Hex Bolts (B) Hex Bolts (B) FIGURE 5. 8. Assemble the upper handle halves to lower handle using five hex bolts (B) and lock nuts —(D). Only tighten finger tight. See figure 5. Hex Lock Nut (D) (Throttle Control Optional) 9. Place the tab on throttle control between the upper handle halves at top holes. Secure with hex bolt (C) and hex lock nut (D) provided in -hardware pack. See figure 6. 10. Tighten securely all six hex bolts and hex lock nuts with 7/16" wrench. FIGURE 6. 11. Secure throttle control wire to handle with two cable ties (E) provided in hardware pack. -See figure 7. 12. Check all nuts and bolts for correct tightness. 13. Slip hand grips (A) on the upper end of each handle. They will slip on more easily if you first soak them in warm, soapy water. 7 I Inner Hole Weld P FIGURE 8. ASSEMBLY INSTRUCTIONS (Loop Handle) 1. Extend throttle control which is attached to the engine at the rear of the mower and place on the floor. Be careful not to bend or kink control wire. —2. Fasten lower handle in position over weld pins in handle mount brackets on deck. Secure with hairpin cotters in inner hole on weld pin. See figure 8. NOTE There are two (2) holes in the handle mount brackets. Place the lower handle against the brackets and secure with hairpin cotter in the inner hole. Inner hole is for operation. Outer hole is for storage. NOTE It may be necessary to pull open the ends of the lower handle. This will insure a tight fit when assembled into handle mount brackets. 3. Assemble upper handle to lower handle. —Secure with two carriage bolts (L or N) and hex lock nuts (O) or hand knobs (M) as shown in figure 9. NOTE There are two height positions for the handle. See adjustment section. ».............................h . I ill ill iiii .——I»■■■■imummea *'V. . -".■ ■îi- ‘' V- i ■ ■- ' ' ■ -V".'- ,.f.' .r-.r, V tfc&Vs 4. Place the throttle control in position on right side of upper handle. Secure with hex bolt (P) —and lock nut (Q). See figure 10. NOTE Reference to right and left hand sides of the unit is observed from the operating position. FIGURE 10. 8 1. FILL SUMP WITH OIL—Use a high quality detergent oil classified “For Service SC, SD, SE or MS”. Nothing should be added to the recommended oil. Control Cable \ 5. Secure throttle control cable to handle with cable ties (R) provided. See figure 11. 6. Check ALL nuts and bolts for correct tightness. FIGURE 11. OPERATION CAUTION DO NOT OPERATE MOWER UNLESS GUARD OR ENTIRE GRASS CATCHER IS IN ITS PROPER PLACE. DAN6ER NOTE For shipping purposes your mower is set with the wheels in a low cutting height position. For best results raise the cutting position until it is determined which height is best for your lawn. See adjustment section. SUMMER (Above 40° F.) Use SAE 30 WINTER (Under 40° F.) Use SAE 5W-20 or SAE 5W-30 KEEP HANDS and FEET AWAY FIGURE 12. Keep hands and feet away from the chute area on cutting deck. See figure 12. If not available, If not available, Use SAE 10W-30 Use SAE 10W or SAE 10W-30 or SAE 10W-40 DIRECTIONS: Place the engine level. Remove oil filler plug. FILL THE OIL SUMP TO POINT OF OVERFLOW. Pour slowly. Capacity VA pints. 2. FILL FUEL TANK—Use clean, fresh, regular grade automotive gasoline. Fill tank completely! DO NOT MIX OIL WITH GASOLINE. 3. When ready to start engine, place throttle control lever on handle in “START” position and start engine in accordance with instructions in engine manual. After engine starts, move throttle control lever on handle to desired engine speed. The engine is stopped by placing control lever on handle in the “STOP” position. 9 I 4. Be sure that lawn is clear of stones, sticks, wire, or other objects which could damage lawn mower or engine. For best results and to insure more even...

Herunterladen

Geben Sie zwei Ziffern: