Stimmen - 3, Durchschnittliche Bewertung: 4
(
)
)
|
Anleitung Zusammenfassung
Depress belt idler and remove the inside (forward) clutch drive belt. See Figure 1.1. REMOVE INSIDE CLUTCH DRIVE BELT WIRING ELECTRIC CLUTCH HARNESS CONNECTOR CONNECTOR FIGURE 1.1 IMPORTANT: The grass catcher kit includes two different length blower drive belts. Carefully check thepart numbers to insure you install the correct belt onyour machine. 1) Belt Part No. 7-2738 fits ZMT and machines with the # 6-3165 Drive Shaft Lowering Kit installed. 2) Belt Part No. 4-6249 fits all other Mid-Mount machines. WARNING DO NOT attempt any maintenance, adjustments or service with engine running. STOP blades. STOP engine. Set brake. Remove key. DO NOT operate machine without entire grass catcher, deflector or guards in place. IMPORTANT: Some models are equipped with a singlebelt drive. To install the catcher on these models, the single groove pulley P/N 4-6969 must be replaced withdual groove pulley P/N 7-2388. The idler pulley P/N 18573 must also be replaced with P/N 3-5867. On MZMModels only, do not use existing P/N 5-8209 belt. Replace with P/N 3-5543. B. Install blower drive belt on inside (forward) pulley of electric clutch. Stretch belt out to the right hand side and lay it over the frame rail. C. Place the other belt in storage for later use. 1.2 DISCHARGE ADAPTER INSTALLATION NOTE: The adapter kits are sold separately based on the size deck on your machine. 61” Decks require Kit No. 6-3076. 52” Decks require Kit No. 6-3077. Disconnect the battery cables. Remove the negative (Black) cable first. Remove the positive (Red) cable last. Remove the deflector as follows: A. Remove cotter pin. B. Remove deflector hinge pin and spring. C. Remove deflector and store it, along with the other parts, for later use. See Figure 1.2. REMOVE COTTER PIN, HINGE PIN, SPRING & DEFLECTOR SPRING COTTER PIN HINGE PIN DEFLECTOR FIGURE 1.2 7 C. Remove discharge-side cutter blade and store for later use. See Figure 1.4. DISCHARGE DISCHARGE - SIDE CUTTER ADAPTER SPINDLE (61” DECKS ONLY) (SEE FIG. 1.3) NEW BLADE TORQUE BLADE PART No. 2-9251 BOLT 70 TO 80 FT. LBS. 1/4” PLATE MUST BE ON TOP PLACE WEIGHTS ON TOP OF AXLE AXLE FIGURE 1.5 (Continued On Next Page) FIGURE 1.4 SECTION 1 – INSTALLATION D. Install the discharge adapter. See Figure 1.3. FIGURE 1.3 INSERT PIN THRU HOLE SECURE WITH COTTER PIN DISCHARGE ADAPTER FASTEN HOOK OVER LIP ON DECK. PUSH DOWN TO SECURE IN PLACE. LIP HOOK 1.3 BLADE INSTALLATION - 61” DECKS ONLY NOTE: Blade Part No. 2-9251 is included in Adapter Kit Part No. 6-3076 for 61” Decks. A. Apply parking brake. B. Use a hydraulic floor jack or hoist to raise machine high enough to gain access to the underside of deck. Secure machine with safety blocks. WARNING Wear heavy leather gloves when handling or workingaround cutting blades. Blades are extremely sharp and can cause severe injury. D. Use blade hardware previously removed to install new kit blade to discharge-side cutter spindle. Refer to Figure 1.4. 1.4 FRONT WEIGHT KIT INSTALLATION WARNING DO NOT attempt any adjustments, maintenance, repairs, service, and unclogging grass tube or deckadapter with the engine running. STOP engine. STOP blade. Engage parking brake. Remove keyfrom ignition switch. Remove spark plug wire(s) and secure wire(s) away from spark plug(s). Engine, muffler and surrounding areas are extremely hot. Allow components to cool down before installing kit. Wear heavy leather gloves when handling or working around cutting blades. Blades are extremelysharp and can cause severe injury. Grass Catchersaffect handling & stability of all machines. Exerciseextreme caution when operating on slopes. DO NOToperate machine on slopes greater than 10 degrees. DO NOT mow across slopes - mow up & down. DO NOT park machine on slopes. A. Remove top nuts and top flat washers on both sides of axle. Place all weights on top of axle. The 1/4” thick plate must be at the top. See Figure 1.5. 8 SECTION 1 – INSTALLATION WARNING DO NOT attempt any adjustments, maintenance, repairs, service, and unclogging grass tube or deckadapter with the engine running. STOP engine. STOP blade. Engage parking brake. Remove keyfrom ignition switch. Remove spark plug wire(s) and secure wire(s) away from spark plug(s). Engine, muffler and surrounding areas are extremely hot. Allow components to cool down before installingkit. Wear heavy leather gloves when handling or working around cutting blades. Blades are extremely sharp and can cause severe injury. GrassCatchers affect handling & stability of all machines. Exercise extreme caution when operating on slopes. DO NOT operate machine on slopes greater than 10degrees. DO NOT mow across slopes - mow up & down. DO NOT park machine on slopes. INSTALL ALL WASHERS AND NUTS. TIGHTEN SECURELY 1.4 FRONT WEIGHT KIT INSTALLATION (Continued From Previous Page) B. Place end brackets on top of weights and front axle. See Figure 1.5A. C. Install all four flat washers and top nuts and tighten securely. See Figure 1.5B. FIGURE 1.5B PLACE END BRACKETS ON TOP OF W...
Dieses Handbuch ist für folgende Modelle:Handrasenmäher - 6-3162 (5.15 mb)