Stimmen - 3, Durchschnittliche Bewertung: 4.3
(
)
)
|
Anleitung Zusammenfassung
Always wear eye protection, gloves and a respirator when operating this unit. Part Number 80702 Rev. 4/02 Shindaiwa Inc. 11975 S.W. Herman Road Tualatin, Oregon 97062 Telephone: 503 692-3070 Fax: 503 692-6696 2002 Shindaiwa, Inc. Part Number 80702 Revision 4/02 Shindaiwa is a registered trademark of Shindaiwa, Inc. Specifications subject to change without notice. Printed in Brazil Introduction This manual contains information for the proper assembly, operation and care of your SP518 sprayer. Carefully read and follow the instructions contained in this manual before operating your sprayer. Pump Chamber Vent Diaphragm Cap Lever Tank Nozzle Wand Trigger Valve THE SERIAL NUMBER IS LOCATED ON THE BOTTOM OF THE TANK. Packing Ring Nut Specifications Net Weight ........................................................ 11 pounds (5.0 kg) Tank Capacity ..................................... 4.75 U.S. gallons (18 liters) Tank Material ............................................................. Polyethylene Fill Opening Diameter .................................. 4.5 inches (114 mm) Pump Type/Material ................................................. Piston/Brass Operating Pressure ....................... 15-90 psi (1.05-6.3 kg/sq. cm) Wand Assembly Length ............................. 29.5 inches (749 mm) Hose Length............................................. 69.75 inches (1771 mm) Nozzle Installed ............................................ Red Adjustable Cone Specifications subject to change without notice. Prepare to Assemble NOTES Wand Tank Unpack the following items shipped in your sprayer box: ¦ Wand ¦ Pump Lever and Connecting Rod ¦ Tank Assembly ¦ Small Parts Kit ¦ From inside the sprayer tank, remove the plastic bag from Connecting Pump Small parts Manual the tank strainer. Rod Lever Kit Trigger Valve Hitch Pins and Washers Small Parts included in the plastic bag Wand Holder Install the Shaft 1. Fit the pump lever Shaft Retaining shaft into the hole Pin in the sprayer base as shown. (chamber side). 2. Push the pump lever shaft in until the hole in the shaft matches the opening in the base reinforcement. 3. Lock the shaft in place with the shaft retaining pin. Install the Wand Holders Pump Lever Shaft Base Reinforcement Fold the wand holders around the pump lever connecting rod, then secure with the screws provided. Screw Connecting Rod Wand Holder 2.5 in. (60 mm) 12 in. (300 mm) 2 11 Shindaiwa Limited Warranty Shindaiwa Inc. manufactures its products to superior standards of quality to ensure customers obtain the highest level of satisfaction. In keeping with this goal, Shindaiwa Inc. warrants the SP518 sprayer to the original purchaser as follows: Warranty Period One year from the delivery date to the original purchaser for consumer and commercial applications. 90 days for rental applications. Warranty Administration Within the covered warranty period, Shindaiwa Inc. will, at their option, repair or replace any defect in material or workmanship, without charge for parts or labor, if this product is presented at an authorized Shindaiwa dealer. Warranty Exclusions and Limitations Shindaiwa Inc. assumes no responsibility for damages, loss, or injury resulting from: ¦ Normal wear and tear ¦ Misuse or neglect ¦ Modifications to or removal of original component parts The warranty is limited to the terms stated herein. Shindaiwa Inc. disclaims all liability for incidental or consequential damages. Some states do not allow the exclusion of incidental or consequential damages, so these limitations may not apply to you. This warranty give you specific legal rights, and you may also have other rights which may vary from state to state. Shindaiwa reserves the right to change the design or specifications of this product without obligation to modify previously manufactured products. Owner’s Responsibilities The owner of the sprayer must demonstrate reasonable care in the use, maintenance, and storage of this Shindaiwa product. If a warrantable failure should occur, the owner must deliver the product to an authorized Shindaiwa servicing dealer for correction. All residual chemicals must be flushed from the sprayer prior to delivery. Unidentified chemicals left in the sprayer tank can pose a serious health threat to anyone servicing the unit and unaware of its presence! To obtain warranty service, proof of purchase must be presented to the authorized Shindaiwa servicing dealer when the product is presented for repairs. Proof of purchase must include date of purchase and the name and address of the selling dealer. Install the Pump Lever and Connecting Rod Hitch Pin Connecting Rod Lever Washer Washer WasherHitch Pin Pump Lever Shaft 1. Lightly grease the end of the pump lever connecting rod and insert into the upper hole in the pump lever. Secure with flat washer and hitch pin. 2. Install a flat washer on the opposite end of the connecting rod. Lightly grease the rod end and insert it into the hole on th...
Dieses Handbuch ist für folgende Modelle:Handrasenmäher - SP518 (817.65 kb)