Stimmen - 2, Durchschnittliche Bewertung: 3
(
)
)
|
Anleitung Zusammenfassung
Inspect and clean the working area before operating. Keep hands, feet, clothing, and hair away from moving parts. Ensure bystanders are clear of the area before operating. START-UP SAFETY Do not let inexperienced operators or children run this equipment. Operate only with ROPS and seatbelt equipped tractors. OPERATION SAFETY Do not permit riders. Do not wear loose fitting clothing during operation. TRANSPORT SAFETY Review Transport Safety instructions in tractor manual before moving. Check with local authorities regarding transport on public roads. Obey all applicable laws and regulations. Make sure the SMV (Slow Moving Vehicle) emblem and all the lights and reflectors that are required by the local highway and transport authorities are in place, are clean, and can been seen clearly by all overtaking and oncoming traffic. Box Scraper 5 SERVICE AND MAINTENANCE SAFETY Stop engine, set brake, remove ignition key, and wait for all moving parts to stop before servicing, adjusting, repairing, or unplugging. Support the equipment with blocks or safety stands before working beneath it. Follow good shop practices including: - keep service area clean and dry - be sure electrical outlets and tools are properly grounded - use adequate light for the job Use only tools, jacks, and hoists of sufficient capacity for the job. Use heavy leather gloves to handle sharp objects. STORAGE SAFETY Store the unit in an area away from human activity. Do not permit children to play on or around the stored machine. Support the frame on stands and blocks to provide a secure base. SAFETY SIGNS The following illustration shows the approximate location and detail of safety signs. Keep all safety signs clean and legible and replace any that are damaged or missing. When original parts are replaced, any safety signs affixed to those parts should be replaced as well. Replacement safety signs are available from your local dealer. INSTALLATION OF SAFETY SIGNS To install safety signs, ensure the installation area is clean and dry. Decide on the exact position before you remove the backing paper. Remove the smallest portion of the split backing paper and align over the specified area. Carefully press in place. Slowly peel back the remaining paper and smooth the remaining portion in place. Small air pockets can be pierced with a pin and smoothed out. Box Scraper 6 ASSEMBLY 1. Bolt the hitch (#2) and hitch braces (#3) to the frame (#1) using hardware supplied. 2. Use the position or draft mode on the three-point control to make a cut at constant depth. Use float when you want the scraper to follow the contour of the ground. The weight of the scraper itself will keep the blade at the desired depth. 3. Use the scarifier shanks to break up hard or packed surfaces. If it is necessary to add weight to the blade, use a maximum of 200 lbs. 4. The two blades allow the operator to scrape or level in either direction. The shanks should be used to break up compacted material ahead of the blade. OPERATION THEORY OF OPERATION 1. Raise the Box Scraper off the ground. 2. Securely block up the frame. 3. Remove shank pins. 4. Install, adjust height or remove as desired. Always keep shanks at the same depth for best results. 5. Install shank pins. Box Scraper 7 MAINTENANCE 1. Raise the Box Scraper off the ground. 2. Securely block up the frame. 3. Remove blade mounting bolts. 4. If the top side of the blade has not been used, reverse and reattach. If it has been used, replace blade. 5. Install mounting bolts and re-tighten. Box Scraper 8 Box Scraper 9 WHEN ORDERING PARTS Always give your dealer the Model, Color and Serial Number of your machine to assist him in ordering and obtaining the correct parts. Use the exploded view and tabular listing of the area of interest to exactly identify the required part. BOX SCRAPER PARTS LIST ITEM PART # DESCRIPTION 1 909628 48" Box Frame 967551 60'' Box Frame 967552 72'' Box Frame 967553 84'' Box Frame 2 F0351 Hitch Weldment 3 906748 Hitch Brace 1/2'' x 3'' x 27 3/4'' 4 909622 48" Cutting Edge 967520 60'' Cutting Edge 967521 72'' Cutting Edge 967522 84'' Cutting Edge 5 967576 Scarifier Shank 967470 Knock-on Point Only 6 967556 Shank Pin 9/16'' x 5'' 7 961012 #16 Hair Pin Clip 8 967361 7/8'' x 4'' Clevis Pin 9 965911 7/16'' Linch Pin 10 965807 Category 1 Top Link Pin 11 906770 Spacer 1''OD x 12GA x 2 1/4'' Long (pl) 12 967524 1/2'' x 1 1/2'' Plow Bolt (pl) 13 81637 1/2'' Lock Washer (pl) 14 81636 1/2'' Hex Nut (pl) 15 84270 5/8'' x 1 3/4'' Hex Bolt (pl) 16 81677 5/8'' Lock Washer (pl) 17 81676 5/8'' Hex Nut (pl) 18 812114 3/4'' x 5 1/2'' Hex Bolt (pl) 19 812365 3/4'' Lock Nut (pl) 20 966527 7/8'' x 2 1/2'' Hex Bolt (pl) 21 81723 7/8'' Lock Washer (pl) 22 81722 7/8'' Hex Nut (pl) Box Scraper 10 SHIPPING KIT AND BUNDLE NUMBERS The following is a list of Kit Numbers for this product and the Bundle Numbers, Descriptions, and Quantities for each Kit. QUANTITY BUNDLE NO. DESCRIPTION Y48BS 48” BOX SCRAPER 1 F0351 Hitch 1 F0801 Frame Y60BS...