Stimmen - 4, Durchschnittliche Bewertung: 4
(
)
)
|
Anleitung Zusammenfassung
1695195 For Prestige / 1800 / 2800, Conquest / 1700 / 2700, & Broadmoor / 1600 / 2600 Series Tractors Instructions This kit is required when installing front mounted snowthrowers. 1 2 Installation Instructions Sub-Frame Hitch Front Pulley - Two-Stage Snowthrower Application Early Manual Lift Only (See Instructions) Hydraulic Lift 47 16 28 27 25 33 40 41 39 38 37 36 43 32 42 33 25 29 29 29 28 28 27 50 17 13 11 14 9 12 13 11 44 51 26 28 27 29 25 19 18 21 20 10 24 23 7 8 9 9 22 15 9 25 49 22 31 30 30 25 27 28 27 33 25 34 32 3 2 1 4 5 6 33 25 28 25 27 26 27 28 35 Front Hole for Dozer Applications Rear Hole for Snowthrower Applications 45 46 48 Main Hitch Components (All Applications) Figure 1. Contents Sub-Frame Hitch Installation Instructions Ref Part No. Qty. Description 1 1723292A 1 SHAFT & HOOK ASSY 2 1653768A 1 CLAMP, Support 3 1931335 4 CARRIAGE BOLT, 5/16-18 x 1 4 1919381 4 WASHER, 11/32 1917356 3 LOCKWASHER, 5/16 6 1917372 4 NUT, 5/16-18 7 105249 1 PIN, Round Head, 3/8 x 2-3/8 8 1724025 1 LIFT LEVER ASSY. 9 2176012 4 SAFETY CLIP 1722946 1 LIFT ROD 11 8031007 2 SET COLLAR 12 171011 1 SPRING, Compression 13 1928721 2 SET SCREW, 5/16-18 x 1/2 14 1723115 1 ROD GUIDE 1733812 2 ROD, Latch 16 1733309 1 ROD, Hitch 17 1733779A 1 HITCH ASSY. 18 1722819 1 PIN, Headless, 1/2 x 2 19 1723795 1 BAR, Lift Link 1960033 1 HAIR PIN CLIP 21 1722469 1 PLATE, Lock, Hydraulic Lift 22 1667812 2 SPACER 23 1960244 1 SCREW, Whiz, 3/8-16 x 2-3/4 24 1921971 1 CAPSCREW, 3/8-16 x 3/4 1924940 8 WASHER PLAIN, 3/8 26 162115 1 BELT GUIDE 27 1916965 7 LOCKWASHER, 3/8 28 1916950 6 NUT HEX FULL, 3/8-16 29 171247 1 PULLEY-FLAT 1666287 1 PULLEY ASS'Y 31 1666294 1 SPACER-BRG 32 1923701 2 CAPSCREW, 3/8-16 x 2 33 158227 4 SPACER 34 1920415 1 CAPSCREW, 3/8-16 x 1-1/4 1722963 1 PIVOT BRACKET 36 1930651 1 NUT LOCK, 3/8-16 37 1704743 1 TRUNNION 38 1668282 1 SPRING 39 1722972 1 GUIDE ASS'Y -SPRING 1960268 1 CARRIAGE BOLT, 3/8-16 x 1-1/4 41 1704741 1 ROD ASS'Y 42 1703371 1 V-BELT, Single-Stage Blower 42 1703372 1 V-BELT, Two-Stage Blower 43 1701600 2 REFLECTOR 44 1922130 1 CAPSCREW, 3/8-16 x 2-1/4 1733814A 1 PUSH BAR LATCH 46 1960074 2 CLIP 47 1921210 4 BOLT, .38-16 x 1 48 1928352 4 NUT- FLG, .38-16 49 1724387 1 PULLY-FLAT 1677135A 1 BELT GUIDE 3 Installation Instructions Sub-Frame Hitch NOTE: Please read through these instructions and the instructions of any other attachments before beginning installation. WARNING Before beginning any service work turn off the PTO, set the parking brake, turn off the ignition, and disconnect the spark plug wire(s). INITIAL ASSEMBLY Assemble Hitch 1. Attach the support clamp (C, Figure 2) and hook assembly (B) to the hitch. Secure with four 5/16-18 x 1 carriage bolts (A), washers (D), lockwashers (E), and nuts (F). Do not tighten the hardware at this time. Figure 2. Install Support Clamp A. 5/16-18 x 1 Carriage Bolt D. 11/32 Washer B. Hook Assembly E. 5/16 Lockwasher C. Support Clamp F. 5/16-18 Nut B C D E A F Conquest / 1700 / 2700 & Prestige / 1800 / 2800 Series B C D E A F Broadmoor / 1600 / 2600 Series Change Pulley & Belt - Two-Stage Blower Only 1. If using this hitch with a two-stage snowthrower, the front idler pulley must be switched from the right hand side of the hitch bracket, to the left, and an additional 3/8 x 1 x 1/2 spacer (B, Figure 3) and 3/8-16 x 2-1/4 capscrew (A) is required. Also install the 1703372 drive belt. A B C D F E Figure 3. Front Pulley - Two-Stage Applications A. Capscrew, 3/8-16 x 2-1/4 D. Washers, 3/8 B. Spacer, 3/8 x 1 x 1/2 E. Lockwasher & Nut C. Belt GuideF. Pulley Assemble Push Bar Latch 1. Attach Push Bar Latch (B, Figure 4), to hitch. Secure with four .31-16 x 1 bolts (A), and four .38-16 flange nuts (C). Figure 4. Assemble Push Bar Latch A. Bolt, .38-16 x 1 C. Flange Nut, .38-16 B. Push Bar Latch Two Wheel A B C Four Wheel Drive Models Drive Models 4 Sub-Frame Hitch Installation Instructions BC D B A Figure 5. Assemble Lift Rod A. Lift Rod C. Spring B. Set Collar D. Rod Guide A B Figure 6. Early/Later Lift Links A. Early Model Lift Link B. Later Model Lift Link Assemble Lift Rod 1. Install the set collars (B, Figure 4), spring (C), and rod guide (D) on the lift rod (A) as shown. Final adjustment of the set collars will be made after the hitch and attachment are installed. INITIAL INSTALLATION Manual Lift Models LIFT LINK - EARLY VS. LATER The early model lift link (A, Figure 6) was used on early production Conquest/1700/2700 Series tractors. It must be replaced with the later model lift link (B) included with this attachment. The later model link works in all applications. Discard the early model link (A). LIFT LINK POSITION The lift link is installed differently depending on what attachment is being used. Refer to Figure 7 for link installation information. Hydraulic Lift Models 1. Fully lower the hydraulic lift. The lift assembly is spring loaded so it will need to be held in the down position to perform of the following procedures. 2. Remove and retain the flat head pin (B, ...