Stimmen - , Durchschnittliche Bewertung:
(
)
)
Hersteller: Agri-Fab
Dateigröße: 813.82 kb
Dateiname: 07124551e.pdf
Unterrichtssprache:
Das Dokument wird geladen, bitte warten
 |
Das Dokument wird geladen, bitte warten
Anleitung Zusammenfassung
45-0381 3-POINT PLUG AERATOR Safety Assembly Operating Maintenance Repair Parts CAUTION: Read Rules for Safe Operation and Instructions Carefully thefastest way to purchase parts PRINTED IN USA FORM NO. 49884 (4/26/07) SAFETY RULES Remember, any power equipment can cause injury if operated improperly or if the user does not understand how to operate the equipment. Exercise caution at all times when using power equipment. LOOK FOR THIS SYMBOL TO POINT OUT IMPORTANT SAFETY PRECAUTIONS. IT MEANS — ATTENTION! BECOME ALERT! YOUR SAFETY IS INVOLVED. CAUTION: VEHICLE BRAKING AND STABILITY MAY BE AFFECTED WITH THE ADDITION OF AN ACCESSORY OR AN ATTACHMENT. BE AWARE OF CHANGING CONDITIONS ON SLOPES. Exercise caution at all times when using power equipment. • Read this owners manual before attempting to assemble or operate the plugger attachment. Be thoroughly familiar with the proper use of this equipment. • Read the vehicle owners manual and know how to operate your vehicle, before using the plugger attachment. • Never allow children to operate the vehicle or plugger attachment and do not allow adults to operate the vehicle or plugger attachment without proper instructions. • This aerator attachment has sharp knife points. Always handle with care and wear substantial foot wear and gloves when operating this aerator. • Do not allow anyone to ride or sit on plug aerator attachment frame or on towing vehicle. • Keep the area of operation clear of all persons, particularly small children and pets. • Always begin with the transmission in first (low) and gradually increase speed as conditions permit. • Tow the 3-point plug aerator at reduced speed over rough terrain and hillsides or near creeks and ditches to prevent tipping over and loss of control. Do not drive too close to a creek or ditch. • Vehicle braking and stability may be affected with the attachment of this plugger attachment. • Before operating vehicle on any grade (hill) refer to the safety rules in the vehicle owner's manual concerning safe operation on slopes. Refer also to the slope guide on page 11 of this manual. Stay off steep slopes! • Do not tow this plugger attachment on highways or on public thoroughfares. • Refer to your vehicle owners manual for information on maximum towing speed. • Follow maintenance and lubrication instructions as outlined in this manual. CARTON CONTENTS 1. Tray 2. Strap (2) 3. Spool Assemblies (4) 4. Axle (2) 5. Axle Support Brackets (4) 6. Mast Extension Straps (2) 7. Mast Side (2) 8. Cross Brace 9 Weight Bracket 128457639 HARDWARE PACK ABCLIJKMNOPHDEFGQRS Ref. Qty. Description Ref. Qty. Description A 1 Hex Bolt, 1/2" x 3-1/2" B 2 Hex Bolt, 1/2" x 2-1/4" C 2 Hex Bolt, 1/2" x 1-1/4" D 2 Spacer, 2.38" E 2 Spacer, 1.65" F 1 Hitch Pin G 2 Spacer, 5.29" H 9 Hex Bolt, 3/8" x 1" I 9 Nylock Nut, 3/8" J 5 Nylock Nut, 1/2" K 16 Washer L 4 Cotter Pin, 1/8" M 8 Flange Bearing N 1 Hair Cotter Pin, 3/32" O 2 Spacer, .75" P 1 Spacer, 1.5" Q 2 Category 1 pin R 2 Lock washer, 7/8" S 2 Nut, 7/8" ASSEMBLY INSTRUCTIONS TOOLS REQUIRED FOR ASSEMBLY (2) Adjustable Wrench (2) 3/4" Open or Box End Wrench (2) 9/16" Open or Box End Wrench (2) 1/2" Open or Box End Wrench (1) Pliers AXLEDKEGKSPOOLASSEMBLYSPOOLASSEMBLYKKKK 2 1. Push split bearings (M) into both ends of each double spool tube. See figure 1. 2. Assemble a washer (K), 1.65" spacer (E), a washer (K), a spool assembly, a washer (K), a 5.29" spacer (G), a washer (K), a second spool assembly, a washer (K), a 2.38" spacer (D) and a washer (K) onto each of the axles. See figure 2. 3. Assemble the cross brace, mast extension straps and mast sides together using two category 1 pins (Q), 7/8" lock washers (R) and 7/8" hex nuts (S). Do not tighten yet. See figure 3. 1 MM QRSCROSS BRACEMAST EXTENSIONSTRAPMAST SIDE 3 4. Attach the weight bracket to the tray using a 3/8" x 1" bolt (H) and 3/8" nylock nut (I). Do not tighten yet. See figure 4. 5. Assemble the straps to the holes in the weight bracket and the tray that are aligned. Use two 1/2" x 2-1/4" bolts (B), .75" spacers (O) and 1/2" nylock nuts (J). Do not tighten yet. See figure 4. 6. Attach the mast extension straps to the front of the tray using two 1/2" x 1-1/4" bolts (C) and 1/2" nylock nuts (J). Do not tighten yet. See figure 5. 7. Assemble the mast sides to the straps using the 1-1/2" spacer (P), 1/2" x 3-1/2" hex bolt (A) and 1/2" nylock nut (J). Do not tighten yet. See figure 5. 8. Tighten all loose nuts assembled through step 7. 9. Attach the four axle support brackets to the tray using eight 3/8" x 1" hex bolts (H) and 3/8" nylock nuts (I). Do not tighten yet! See figure 6. 10. Secure the axles to axle support brackets using two washers (K) and 1/8" x 1-1/2" cotter pins (L) at the ends of each axle. See figure 7. 11. Tighten the four axle brackets assembled in step 10. See figure 7. 12. Add grease to the spool assemblies through the grease fittings until grease is forced out the ends of the spool tubes. See figure 7. 6...