Stimmen - 2, Durchschnittliche Bewertung: 4
(
)
)
|
Anleitung Zusammenfassung
3. Only use extension cables specifically designed for outdoor use. CONNECTORS - IMPORTANT • Flymo connectors are suitable for use with 2 core cable only. Under no circumstances should these connectors be used for earthed products. • All Flymo connectors and cables are of splashproof construction. They are not waterproof and must not be left outside permanently nor should they be submerged or immersed in water. Do not let cable lay or trail through pools of water or splashed with water from hose pipes. MAINS PLUG REPLACEMENT - IMPORTANT • If the plug supplied is cut off it should be destroyed. There is an electric shock hazard if a cut off plug is inserted into a 13 amp socket. 1. No earth required. Flymo products are double insulated to EN60335 and under no circumstances should an earth be connected to any part of the product. 2. Ensure the mains voltage suits your product 3. IMPORTANT! The wires in the mains lead are coloured in accordance with the following code: BLUE -NEUTRAL BROWN -LIVE The wire which is coloured BLUE must be connected to the Terminal which is marked with the letter 'N' or coloured BLACK. The wire which is coloured BROWN must be connected to the Terminal which is marked with the letter 'L' or coloured RED. 4. It is important that the outer sheath is clamped correctly into the 3-pin plug. 5. If in doubt consult your local Service Repairer or qualified electrician before the machine is used. 6. A 13 Amp fuse must be fitted to the Mains Plug. 7. The normal plug fuse and household fuse only protect the electrical equipment and are not a safeguard against electrocution. If your product is hard wired i.e. non-detachable mains electric cable, a conversion kit and extension cable is available from all Approved Service Centres which can be found in your local Yellow Pages. A • The Loose Parts Pack is packaged underneath the deck. Assembly of Lower Handles to Deck 1. Place the bolt (A2) through the hole in the lower handle (A1) until the lower handle fits into the recess (A3) 2. Place the washer (B1) and the wing knob (B2) on to the bolt and tighten the wing knob. 3. Repeat on the other side. Assembly of Upper Handles to Lower Handles. 1. Ensure the upper handle is located correctly with the lock-off button on the switchbox uppermost. 2. Ensure the upper handle (C1) and the lower handle (C2) are aligned correctly. 4. Fit the bolts (C3), washers (C4) and wing knobs (C5). Tighten the wing knob. 5. Fit the cable to the handles with the clips provided. Make sure the cable is not trapped between the upper and lower handles. Grassbox Assembly 1. Slide the grassbox tongue into the slots in the grassbox lower until it clicks securely into position (D) 2. Push the grassbox handle into the slots in the grassbox upper until it clicks securely into position. (E) 3. Starting at the rear of the grassbox, locate the grassbox upper into the grassbox lower by aligning the clips (F1). Ensure all clips are correctly located.(F2) before clicking into position. 4. Clip the two halves together, ensuring all clips are securely connected. Assembly Instructions B C D 1 E F1 F2 2 3 1 2 1 2 3 4 5 Cutting Height Adjustment Grassbox Cutting Height Adjustment (K) & (L) • Height of cut is adjusted by raising or lowering the Front and Rear Wheels. • There are five heights of cut on this product. • NOTE A medium height of cut is recommended for most lawns. The quality of your lawn will suffer and collection will be poor if you cut too low. HEIGHT OF CUT WHEELS POSITION Low Front position 2cm Rear position 2cm Low to Medium Front position 2cm Rear position 4cm Medium Front position 4cm Rear position 4cm Medium to High Front position 4cm Rear position 6cm High Front position 6cm Rear position 6cm K L 2cm J Fitting Fully Assembled Grassbox to Lawnmower. 1. Lift safety flap (G1) 2. Make sure the discharge chute is clean and free from debris (G2) 3. Locate fully assembled grassbox onto 2 location points (G3) at the rear of the deck as illustrated in pic. H 4. Locate safety flap onto the top of the grassbox. Ensure the grassbox is securely located. • IMPORTANT ! AFTER FITTING ENSURE NO GAP REMAINS BETWEEN THE SAFETY FLAP AND THE GRASSBOX. • Removal is the reverse procedure. • For larger areas of grass where grass collection is not required you can use your lawnmower without the grassbox. Ensure the Safety Flap is fully closed. The design of the safety flap permits the cut grass to be discharged downward behind the machine. Grassbox Full Window (Visimo Only) • As the grassbox fills up, grass will be visible through the window (J). • When the window/grassbox is full it is time to empty the grassbox. grassbox empty grassbox full G 1 2 3 H Visimo Only 6cm 4cm M N R Starting and Stopping To Start your Lawnmower 1. Form loop in mains cable and push the loop through the slot. (M) 2. To secure, position loop over the hook and pull the cable back through the slot (N). 3. Connect plug to mains and switch on. 4. Tilt the handle downwards to sli...
Dieses Handbuch ist für folgende Modelle:Handrasenmäher - ROLLERMO RM032 (6.07 mb)