Stimmen - 1, Durchschnittliche Bewertung: 3
(
)
)
|
Anleitung Zusammenfassung
10. Continue supplying shortening to the kettle as required. Keep the kettle filled up to the “Oil Level” marks on the side. 11. When you are done frying donuts, move the on/off switch to the OFF position. Belshaw Bros., Inc. .. 1750 22nd Ave. S. .. Seattle, WA 98144 .. Phone 206-322-5474 .. Fax 206-322 618L, 624, and 634 Electric Fryers MN-1126EN Cleaning 3 For your safety, observe the following warnings throughout the entire cleaning process. WARNING Thoroughly clean and dry the floor if shortening, water, or other materials are spilled. Materials spilled on the floor can cause serious injury or loss of life. WARNING To avoid electrocuting yourself or damaging the machine, never allow water, steam, shortening, cleaning solution, or any other liquid to enter the electrical box or the heater head. WARNING To avoid being burned in an explosion, never use any flammable materials for cleaning. Cleaning the Exterior Surfaces 1. Clean the polished and painted surfaces of the fryer with a soft, damp cloth. Use a nonabrasive cleaner to remove any discoloration. 2. Polish these surfaces with a soft, dry cloth. Cleaning the Frying Screen 1. In a sink or a dishwasher, wash the frying screen using warm water and mild detergent. Do not use an abrasive cleaner or scraper. 2. Rinse the frying screen in clear water. 3. Dry the frying screen thoroughly, using a soft cloth, before you use it again. WARNING Dry the frying screen thoroughly. Moisture causes hot shortening to spatter, which may cause serious injury. 4. Check the frying screen to make sure no metal is flaking off of it. If the screen is flaking, replace it immediately, so you do not get metal particles in your product. Cleaning the Kettle There are four basic steps to cleaning the kettle: removing the shortening, washing, rinsing, and drying. You must perform all four steps and perform them in the order listed. Removing the Shortening WARNING To avoid being burned or electrocuted, disconnect the fryer from the power source before cleaning it. 1. Disconnect the machine from the power source. 2. Let the shortening cool to 100. F/38. C. Belshaw Bros., Inc. .. 1750 22nd Ave. S. .. Seattle, WA 98144 .. Phone 206-322-5474 .. Fax 206-322 MN-1126EN 618L, 624, and 634 Electric Fryers 3. Place a Belshaw Shortening Filter or a large metal container under the drain valve of the fryer. WARNING Do not use a plastic container. If the shortening is not cool enough, the container will melt, possibly causing you to be burned, and causing shortening to get on the floor. 4. Open the drain valve by turning the drain valve extension knob on the side of the fryer cabinet. Allow all the shortening to drain into the Shortening Filter or metal container. 5. If you are using a metal container, watch it to make sure the shortening does not overflow. If the container becomes full, close the drain valve, put another metal container under the drain valve, and open the drain valve again. WARNING Do not allow the shortening to overflow the containers. Shortening will get on the floor, and if the shortening is not cool enough, you may be burned. WARNING Thoroughly clean and dry the floor if shortening is spilled. Shortening on the floor can cause serious injury or loss of life. 6. If you have drained the shortening into a metal container and you wish to re-use the shortening, set the container of shortening aside. Place another suitable container under the drain valve. 7. Brush accumulated carbon from the heating elements. Accumulated carbon causes corrosion and poor heat recovery. 8. Tilt the heater head assembly out of the fryer and lock it in place. 9. Using a non-abrasive, non-metallic spatula, scrape the sediment and any remaining shortening through the drain valve. 10. Close the drain valve. 11. If your fryer has a Belshaw Shortening Melter (FM) connected to it, install the plug into the reservoir nipple. Washing 1. Carefully pour hot water into the kettle, up to the normal level of the shortening. Add trisodium phosphate or another appropriate cleaner. 2. Scrub the inside of the kettle. Do not use any abrasive cleaners or scrapers. WARNING To avoid being burned, be very careful as you work with hot cleaning solution. Never put your hands in the solution. Wear gloves and long sleeves in case any solution splashes. 3. Allow the cleaning solution to cool to the touch. 4. Place a large metal container under the drain valve. WARNING Do not use a plastic container. If the cleaning solution is not cool enough, the container will melt; possibly causing you to be burned, and causing cleaning solution to get on the floor. 5. Open the drain valve and allow the cleaning solution to drain into the container. Belshaw Bros., Inc. .. 1750 22nd Ave. S. .. Seattle, WA 98144 .. Phone 206-322-5474 .. Fax 206-322 618L, 624, and 634 Electric Fryers MN-1126EN 6. Watch the container to make sure the cleaning solution does not overflow. If the container becomes full, close the drain valve, put another large meta...
Dieses Handbuch ist für folgende Modelle:Friteusen - 618L (1.46 mb)
Friteusen - 618L (1.46 mb)
Friteusen - 624 (1.46 mb)
Friteusen - 634 (1.46 mb)