Stimmen - 3, Durchschnittliche Bewertung: 4.7 ( )

Hersteller: Electrolux Dateigröße: 1.41 mb Dateiname: Unterrichtssprache:

This applies especially to safety and control elements. Parts requiring replacement are only to be replaced by original spare parts. A service contract is recommended. ▲ Cleaning and maintenance must be done only when the heating surfaces are cold. Do not use inflammable liquids to clean the appliance. ▲ An obligatory service check is required annually. 2. TECHNICAL DATA PNC Appliances Appliance type Voltage Width Depth Height Trough contents Power V inch mm in kW 9CHG584093 WFWROFOOOO 208 19.7 35.4 35.4 500 900 900 6.1 gal 1 x 23 l 12.2 9CHG584094 WFXROFOOOO 240 13 9CHG584095 WFWROAOOOO 208 12.2 9CHG584096 WFXROAOOOO 240 13 9CHG584097 WFWUOFOOOO 208 31.5 35.4 35.4 800 900 900 3.7 gal 2 x 14 l 18.4 9CHG584098 WFXUOFOOOO 240 20.8 9CHG584099 WFWUOAOOOO 208 18.4 9CHG584100 WFXUOAOOOO 240 20.8 3. PACKAGING All the packaging materials used are environmentally friendly. They may burnt at an incineration plant or sent for recycling. 4. TESTS / CERTIFICATES All electrical appliances are UL 197 tested. 5. SPECIFICATION PLATE The specification plate (E) is located in each case inside and outside on the right of the operator panel (C) (Page 5 Fig. 5). The serial number is marked on the type plate. The 8 digits give following information: Y last digit of the year of production WW week of production XXXXX running number 62.9585.01 UL Page 3 0] Electrolux INSTALLATION INSTRUCTIONS II . INSTALLATION INSTRUCTIONS 1. INSTALLATION The appliance is designed for connection to fixed lines. The appliances are suitable for setting up as single appliances or as a group of appliances. They can be set up freely in the room, side by side, at the side and/or at the back against a wall. Gaps between two appliances or appliance and sidewall should be filled with a FDA approved silicone such as Samco RTV103. 1.1 DISTANCES If an appliance is set up next to or against temperature-sensitive furniture or similar, a safety gap of approximately 6“ (15 mm) should be maintained or some form of heat insulation fitted. The walls must be made up of non-combustible material like tiles or steel. 1.2 HEIGHT ADJUSTMENT Appliance on feet: Alignment is carried out by screwing the lower foot parts in or out. Appliance on Irregularities or differences in height can steel plinth: be equalized by inserting one or several strips of chrome nickel steel. Appliance on feet. O Turn the lower part of the feed to adjust the appliance high. The feet are adjustable from 4“ to 8“ (100 to 200 mm). A high of 8“ (200 mm) can be recommended and results in an appliance high of 35,4“ (900 mm). Note: Adjustment of the legs shall provide an unobstructed clearance of minimal 6“ (150 mm) and maximal 8“ (200 mm) beneath the unit due to sanitary and stability aspects. The lower part of the foot must not be unscrewed too far. The exposure of threads is prohibited. 1.3 ASSEMBLING TWO APPLIANCES Fig.1 Lateral connection The assembly kit contains three of each of the following: caged nuts (1 / Fig.1) pre-assembled on the right-hand side of the appliance, hexagonal screws M8x25 (1 / Fig.1), bolts with retaining rings (2 / Fig.1) and mounting links (3 / Fig.1) O Remove the control panels from both appliances as in 2.2 O Remove the front panels from both appliances as in 2.1 O Insert the bolts with the retaining rings (2 / Fig.1) from outside into the guide in the right-hand connecting plate. O Keeping the screw (3 / Fig.1) loose, turn it until it is approximately 5 mm deep in the caged nut. Positioning the appliances: O Place the appliances next to one other. O Align for position and height. Connect the appliances: O Push the appliances together so that the bolts (1 / Fig.1) engage in the guides of the appliance to be attached. O Fit the mounting link (3 / Fig.1) into the inside of the second appliance's left connecting plate. O Tighten the screws. Note If required, the caged nuts can also be fitted on the other side of the appliance. The connection of two appliances (Fig 1c, arrow) must correspond to the hygienic regulations respective the standard NSF/ANSI 4. All resulting joints and seams in a splash zone shall be sealed and smooth. Page 4 62.9585.01 UL INSTALLATION INSTRUCTIONS H Electrolux 1.4 SIDEWALL (D) 1.6 ASSEMBLING ON CASTORS Fig.2 Assemblage of sidewall The assembly kit contains two of each of the followi...

Herunterladen

Geben Sie zwei Ziffern: