Stimmen - 3, Durchschnittliche Bewertung: 4 ( )

Hersteller: Bakers Pride Oven Dateigröße: 3.66 mb Dateiname: Unterrichtssprache:

7. Tighten the spin handle until the lid is firmly sealed. Then line up the orange knob on the spin handle with the orange knob at the front of the fryer. 8. Activate the timer by pressing the START/STOP button on the digital timer. The timer will begin the count down. 9. At the end of the frying cycle, the digital timer beeper will sound and the fryer will automatically release pressure into the baffle box. Press the START/STOP button. 10. When the pointer on the pressure gauge is at zero, wait 5 seconds then slowly turn the spin handle counterclockwise to break the seal around the lid. The fryer has a locking pin that prevents turning the spin handle until the pressure drops to zero. Do not force the spin handle to open the lid. 11. Slowly open the lid. Failure to use the insulated mitts will result in injury. Always use the insulated mitts when handling the hot fry basket. 12. Lift the basket and hang it on the front of the fryer pot to drain. 13. Empty the basket. 16 Electric Pressure Fryer Operation 14. Remember to filter the shortening at least every third frying cycle load. Refer to the procedure in this manual. Also filter the shortening and clean the fryer at the end of each day. If you do not plan to use the fryer for an hour or more, turn the thermostat down to 150 and close the lid. 15. When you have finished frying for the day, turn the FILTER/OFF/FRY switch to the OFF position. FKM-FC Operation System Programming Use the following figure and table to set options that apply to each product programs. Figure 1. System Programming Sequence 17 Electric Pressure Fryer Operation Table 1. System Programming Procedure STEP ACTION DISPLAY COMMENTS 1 Press the FILTER/OFF/FRY switch to FRY. LOW 2 Press PROG on the keypad. PROGRAM CODE 3 Input 1712 and ENTER. PROGRAM SYSTEM 4 Press ENTER. PROGRAM DEGREES °F This command allows you to choose the temperature scale option you want to use. The display will show either show °F or °C. 5 Press TOGGLE/CLEAR until the desired option is displayed. PROGRAM DEGREES X X refers to the temperature scale you have chosen. 6 Press ENTER. PROGRAM APL TYPE ELECTRIC This command allows you to choose the appliance type you are using. The display may show ELECTRIC, GAS OR ALF. 7 Press TOGGLE/CLEAR until the desired option is displayed. PROGRAM APL TYPE X X refers to the appliance type you have chosen. 8 Press ENTER. PROGRAM MELTCYCL YES This command allows you to set the melt cycle option. This is normally set to yes if you are using solid shortening. The display will show either YES or NO. 9 Press TOGGLE/CLEAR until the desired option is displayed. PROGRAM MELTCYCL X X refers to the melt cycle option chosen. 10 Press ENTER. PROGRAM GLBLFLTR 0 This command allows you to specify the total number of fry cycles to complete among all product programs before a message is displayed reminding you to filter the shortening (filter lockout). 11 Press TOGGLE/CLEAR and input the number of fry cycles you want to complete among all product programs before enabling filter lockout. PROGRAM GLBLFLTR X X refers to the number of program cycles you want to complete among all product programs before filtering the shortening. 12 Press ENTER. PROGRAM SYSTEM 13 Press PROG to exit the programming mode. LOW 18 Electric Pressure Fryer Operation Product Programming Use the following figure and table to set a maximum of eight product programs. The product programs must be set before cooking can begin. Figure 2. Product Programming Sequence 19 Electric Pressure Fryer Operation Table 2. Product Programming Procedure STEP ACTION DISPLAY COMMENTS 1 Press the FILTER/OFF/FRY switch to FRY. LOW 2 Press PROG on the keypad. PROGRAM CODE 3 Input 1724 and press ENTER. PROGRAM PRODUCT # 4 Select the program product number (1-8). PROGRAM PRODUCT X X refers to the program number you selected. 5 Press ENTER. PROGRAM TIME1 00:00 This command allows you to specify the cooking time for this stage. The time displayed may be a previously programmed value. 6 Press TOGGLE/CLEAR and input the number of minutes you want to cook. PROGRAM TIME1 XX:XX XX:XX refers to the number of minutes you input. 7 Press ENTER. PROGRAM TEMP1 000 °F This command allows you to specify the cooking temperature for this stage. The temperature displayed may be a previously programmed temperature. The temperature scale may also display °C depending on the system option that is set. 8 Press TOGGLE/CLEAR and input the cooking temperature for product to be cooked. PROGRAM TEMP1 XXX °F XXX refers to the cooking temperature you input. 9 Press ENTER. PROGRAM TEMPCOM1 FLEX TIME This command enables you to select whether or not time is allowed for the fryer to recover from temperature loss while cooking during this stage. The FLEX TIME option will allow the fryer to recover from temperature loss. 10 Press TOGGLE/CLEAR until the desired option is displayed. PROGRAM TEMPCOM1 X X refers to the temperature compensation option selected. 11 Press ENTER. PROGRAM VALVE1...

Herunterladen

Geben Sie zwei Ziffern: