Stimmen - 0, Durchschnittliche Bewertung: 0
(
)
)
|
Anleitung Zusammenfassung
53 mm (1 7/16 . 2 3/4 . 2 1/8 inches) (w/h/d) Mass Approx. 70 g (2 1/2 oz) Accessories (supplied) Pouch (1) Operating instructions (1) Accessory (not supplied) Halogen lamp XB-3D Design and specifications are subject to change without notice. AAttaching or removing the video flash light to a camcorder To attach the video flash light Set the power switch to OFF before attaching it to a camcorder. 1 Insert the video flash light into the intelligent accessory shoe of your camcorder in the direction of the arrow on its bottom until it reaches the end and you hear it click. 2 Turn the lock knob to LOCK and tighten it until you hear it click. To remove the video flash light 1 Set the power switch to OFF. 2 Loosen the lock knob by turning it to RELEASE. 3 Push down and pull out the video flash light in the opposite direction of the arrow to remove it. Notes •If you cannot insert the video flash light, turn the lock knob to RELEASE to cancel the lock. •Do not insert the light backwards. Be sure to insert the light in the direction of the arrow. •The video light can turn 270 degrees. You can turn it in any direction you like to use. B Using the video flash Use the video flash only with a camcorder which has the PHOTO recording function. The DCR-TRV50 is the model used for illustration purposes. For details, refer to the operating instructions of your camcorder. 1 Set the camcorder POWER switch to CAMERA. Set the camcorder POWER switch to MEMORY when recording a still image on a “Memory Stick”. 2 Set the power switch to ON. The charge complete lamp READY blinks as the video flash light starts to charge. When charging is complete, the charge complete lamp READY stops blinking but remains on. 3 Keep pressing the camcorder PHOTO button lightly to confirm the image. Keep the camcorder PHOTO button pressed down lightly. The flashing of the video flash light is linked to the PHOTO button. A still picture appears in the viewfinder and the memory indicator comes on. Recording is not carried out at this point. To change the still picture, release the camcorder PHOTO button. The video flash light starts charging again after you release the camcorder PHOTO button. Wait until the battery charge complete lamp READY appears before lightly pressing the PHOTO button again. Because the camcorder automatically adjusts the brightness when you press the PHOTO button, the image may get darker or the colors may seem to change. 4 Press the camcorder PHOTO button deeper. When you press the PHOTO button, the bar scroll indicator disappears and recording stops. During recording, captured images appear in the viewfinder or on the LCD. When you release the PHOTO button, the video flash light automatically starts to recharge after the image is recorded. After use Set the power switch to OFF. Notes •The appropriate distance between a subject and the video flash light is approx. 1 m to 5 m in a dark room. •During recording, keep your fingers away from the sensor A of this unit. Otherwise, the brightness of the flash cannot be adjusted properly. •The video flash light uses the same battery as your camcorder. If the battery level is low, the flash light takes more time to recharge. •The video flash light will be recharged even if it is completely charged after: - you set the power switch to OFF. - you set the camcorder standby switch to other positions, LOCK or STANDBY. •The video flash light has a red-eye prevention function (to stop people's eyes appearing red in photos), but this might not work depending on the specifications of your camcorder. C Using the video light To turn on the video light automatically in a dark place 1 Set the power switch to LIGHT AUTO. 2 Set the camcorder to standby mode. The video light turns on automatically when using the camcorder in a dark place. The video light turns off automatically after approx. 5 minutes in the standby mode. To turn off the video light when the light is on, switch the camcorder to OFF or LOCK. To control the video light with the camcorder in standby mode 1 Set the power switch to LIGHT ON. 2 Set the camcorder to standby mode. The video light is turned on in sync with the camcorder. To turn off the video light, switch the camcorder to OFF or LOCK, or switch the video light to OFF. After use Set the power switch to OFF. Notes •The battery discharges while the camcorder is in standby mode. Be sure to switch from standby to OFF or LOCK. •Store in pouch when not in use. •Make sure the video light has cooled down before storing it. D Lighting up a subject •When recording indoors with this unit, you can get clear and beautiful color pictures. •For wide angle shots, the video light may not light the corners of pictures completely. Use the video light for shooting the main subject of the picture effectively. •When bright light shines from behind the subject (backlighting), the video light is very effective for lighting up the main part of the subject, such as the person’s face. Outdoors, be sure that yo...