Stimmen - 2, Durchschnittliche Bewertung: 4.5
(
)
)
|
Anleitung Zusammenfassung
• Even if the CHARGE lamp is not lit, the battery charger is not disconnected from the AC power source (mains) as long as it is connected to the wall outlet (wall socket). If some trouble occurs while using the battery charger, immediately shut off the power by disconnecting the plug from the wall outlet (wall socket). • When charging is finished, disconnect the power cord (mains lead) from the wall outlet (wall socket), and remove the Nickel-Metal Hydride batteries from the battery charger. • Time required to charge fully depleted Nickel-Metal Hydride batteries at a temperature of 25°C (77°F). Charging may take longer under certain circumstances or conditions. • The CHARGE lamp may remain lit longer than six hours, but this is not a malfunction. Nickel-Metal Hydride battery Charging time NH-AA-DA.2 (supplied) Approx. 6 hours 1 Battery charger 2 Connect the power code (mains lead). 3 To wall outlet (wall socket) Power cord (mains lead) 1 Insert the batteries. Charging indicator Light on: Charging Light off: Completed (Remove the batteries.) Match 3/# and insert. Using batteries other than the supplied ones You can use HR 15/51:HR6 (size AA) Nickel-Metal Hydride batteries/R6 (size AA) alkaline batteries/ZR6 (size AA) Oxy Nickel Primary Battery. t “User’s Guide/Troubleshooting” (page 91) Using the AC Adaptor You can connect the camera using the AC-LS5K AC Adaptor (not supplied). t “User’s Guide/ Troubleshooting” (page 16). Refer to the operating instructions supplied with the AC Adaptor. To check the remaining battery time Press POWER to turn on and check the time on the LCD screen. To remove the batteries Hold the camera with the battery cover facing upward, then open the battery cover and remove the batteries. Be careful not to drop the batteries. To use your camera abroad — Power sources You can use your camera, the supplied battery charger, and the AC Adaptor (not supplied) in any country or region where the power supply is within 100 V to 240 V AC, 50/60 Hz. Use a commercially available AC plug adaptor [a], if necessary, depending on the design of the wall outlet (wall socket) [b]. Battery remaining indicator Battery remaining guidelines Sufficient power remaining Battery half full Battery low, recording/ playback will stop soon. Change the batteries with fully charged ones, or charge the batteries. (The warning indicator flashes.) • The displayed time remaining may not be correct under certain circumstances. • When using alkaline batteries/Oxy Nickel Primary Battery, the battery remaining indicator does not display the correct information. • When the AC Adaptor (not supplied) is used, the battery remaining indicator is not displayed. • Do not use an electronic transformer (travel converter), as this may cause a malfunction. BC-CS2A/ CS2B Turn the camera on/set the clock 2 1 Select . 2 Press POWER. 2005 / 1 / 1 12 : 00 AM OK Cancel Clock Set D/M/Y M/D/Y Y/M/D Lighting 3 Set the clock with the control button. 1 Select the date display format with v/V, then press z. 2 Select each item with b/B and set the numeric value with v/V, then press z. 3 Select [OK] with B, then press z. • To cancel, select [Cancel] and press z. 2005 / 1 / 1 12 : 00 AM OK Cancel Clock Set D/M/Y M/D/Y Y/M/D 2005 / 1 / 1 12 : 00 AM OK Cancel Clock Set D/M/Y M/D/Y Y/M/D 2005 / 1 / 1 10 : 30 AM OK Cancel Clock Set D/M/Y M/D/Y Y/M/D To change the date and time Select [Clock Set] in the (Setup) screen and perform the procedure in step 3 above. t “User’s Guide/Troubleshooting” (page 54) On the clock display • If you selected [D/M/Y] in step 3-1, set the time on a 24-hour cycle. • Midnight is indicated as 12:00 AM, and noon as 12:00 PM. When turning on the power • Unless you set the clock, the Clock Set screen appears each time the camera is tu...
Dieses Handbuch ist für folgende Modelle:Kameras - DSC-W15 (466.78 kb)
Kameras - DSC-W17 (466.78 kb)
Kameras - DSC-W7 (466.78 kb)