Stimmen - 2, Durchschnittliche Bewertung: 4.5
(
)
)
|
Dieses Gerät hat auch andere Anweisungen:
Anleitung Zusammenfassung
Tap H to return display to the previous screen. Image mode White balance Exp. +/- Continuous For accurate color reproduction, choose a setting that matches the light source. White balance Introduction 15 First Steps Charging the Battery First Steps Charging the Battery The camera uses a Rechargeable Li-ion Battery EN-EL10 (supplied). Charge the battery with the Battery Charger MH-63 (supplied) before first use or when the battery is running low. 1 Connect the power cable. Connect the power cable to the battery charger 1 and insert the wall plug into a power outlet 2. The CHARGE lamp will light to show that the charger is on 3. First Steps 123 2 Charge the battery. Insert the battery at an angle as shown 1, and set it in the battery charger 2. 12 CHARGE lamp starts blinking when 3 4 battery is inserted 3. Charging is complete when lamp stops blinking 4. About 100 minutes are required to charge a fully depleted battery. 16 Charging the Battery The following chart explains CHARGE lamp status. CHARGE lamp Description Blinks Battery charging. On Battery fully charged. Flickers • The battery is not inserted correctly. Remove the battery and reinsert it into the battery charger so that the battery is lying flat. • Charge the battery indoors with an ambient temperature of 5 °C to 35 °C (41 °F to 95 °F) before use. • The battery is faulty. Stop charging immediately, unplug the charger, and take both the battery and charger to your retailer or Nikon service representative. 3 Remove the battery and unplug the charger when charging is complete. B Notes on the Battery Charger • The supplied battery charger is for use only with the Rechargeable Li-ion Battery EN-EL10. Be sure to use only genuine Nikon brand rechargeable batteries. • Be sure to read and follow the warnings for the battery charger on page iii before using the battery charger. B Notes on the Battery • Be sure to read and follow the warnings for the battery on page iii and the section, “The Battery” (A 146), before using the battery. • If the battery is not used for an extended period, recharge it at least once every six months and run it flat before returning it to storage. C AC Power Supply To power the camera continuously for extended periods, use an AC Adapter EH-62D (available separately from Nikon) (A 143). Do not, under any circumstances, use another make or model of AC adapter. Failure to observe this precaution could result in overheating or in damage to the camera. 17 First Steps 18 First Steps Inserting the Battery Insert a Rechargeable Li-ion Battery EN-EL10 (supplied) into your camera. • Charge the battery before the first use or when the battery is running low (A16). 1 Open the battery-chamber/memory card slot cover. 2 Insert the battery. Confirm that the positive (+) and negative (–) terminals are oriented correctly as described on the label at the entrance of the battery chamber, and insert the battery. Use the battery to push the orange battery latch in the direction indicated by the arrow 1 and fully insert the battery 2. When the battery is fully inserted, the battery latch will lock it in place. B Inserting the Battery Inserting the battery upside down or backwards could damage the camera. Be sure to check the battery is in the correct orientation. 3 Close the battery-chamber/memory card slot cover. Inserting the Battery Removing the Battery Turn the camera off and make sure that the power-on lamp and the monitor have gone out before opening the battery-chamber/memory card slot cover. To eject the battery, open the battery-chamber/ memory card slot cover and slide the orange battery latch in the direction indicated by the arrow 1. The battery can then be removed by hand 2. • Note that the battery may become hot during use; observe due caution when removing the battery. Turning On and Off the Camera To turn on the camera, press the power switch. The power-on lamp (green) will light for a moment and the monitor will turn on. To turn off the camera, press the power switch again. When the camera is turned off, both the power-on lamp and monitor will turn off. • If the camera is turned off, hold down the c button to turn the camera on in playback mode (A 31). C Auto Power Off in Shooting Mode (Standby Mode) If no operations are performed for about a minute (default setting), the monitor will turn off automatically and the camera will enter standby mode. If no operations are performed for another three minutes, the camera will turn off automatically (the auto off function). Pressing the power switch, or the shutter-release button, while the monitor is off in standby mode will reactivate the monitor. The time allowed to elapse from before the camera enters standby mode can be changed from the Auto off option (A 136) in the setup menu (A 127). First Steps 19 Setting Display Language, Date and Time A language-selection dialog is displayed the first time the camera is turned on. 1 Press the power switch to turn on the camera. The power-on lamp (gre...