Stimmen - 2, Durchschnittliche Bewertung: 3
(
)
)
|
Dieses Gerät hat auch andere Anweisungen:
Anleitung Zusammenfassung
To reduce red-eye, a series of low-intensity pre-flashes fire before the main flash. In addition, if the camera detects red-eye when an image is taken, the affected area is processed to reduce red-eye before the image is saved. Note the following when shooting: • Due to the pre-flashes, there is a longer than usual interval between the time the shutter-release button is pressed and the time the shutter is released. • More time than usual is required to record images. • Red-eye reduction may not produce the desired results in some situations. • In extremely rare instances, areas not subject to red-eye may be affected by red-eye reduction processing; in these cases, choose another flash mode and try again. Shooting Features 45 Basic Shooting Settings Using the Self-timer The camera is equipped with a 10-second and 2-second timer for self-portraits. This feature is useful for reducing the effects of camera shake that occurs when pressing the shutter-release button. When using the self-timer, use of a tripod is recommended. Set Vibration reduction to Off from the setup menu (A74) when using a tripod to stabilize the camera. Shooting Features1 Tapthe self-timer icon. 2TapYor Z. •Y10 s: Use on important occasions, such as weddings. •Z2 s: Use to prevent camera shake. •The selected self-timer mode is displayed. 3Frame the picture andpressthe shutter-release button halfway. •Focus and exposure are locked. [ 930][930][ 930] Sef-timer10 s 2 s Off1 /250F321/250F3.21 /250F32 46 Basic Shooting Settings 4 Press the shutter-release •To stop the timer before an image is taken, press the shutter-release button again. 1 /250F321/250F3.21 /250F329 button the rest of the way down. • The self-timer starts, and the number of seconds remaining before the shutter is released is displayed in the monitor. The self- timer lamp flashes while the timer is counting down. About 1 second before the shutter is released, the lamp stops flashing and glows steadily. • When the shutter is released, the self-timer turns off. Shooting Features 47 Basic Shooting Settings Using Macro Mode When using macro mode, the camera can focus on objects as close as approximately 10 cm (4 in.) from the front of the lens. This feature is useful when taking close-up images of flowers and other small subjects. 1 Tap the macro mode icon. [ 930][930][ 930] 2 Tap o. Macro modeOnOff 3 Use the zoom control to set the zoom ratio to a position where Fand the zoom indicator glow green. TW • How close you can be to the subject when shooting depends on the zoom ratio. When the zoom ratio is set to a position where Fand the zoom indicator glow green, the camera can focus at subjects as close as approximately 30 cm (1 ft) from the lens. When the zoom is at the maximum wide-angle position (at the position where Gis displayed), the camera can focus on subjects as close as approximately 10 cm (4 in.) from the lens. B Note About Using the Flash The flash may be unable to light the entire subject at distances of less than 50 cm (1 ft 8 in.). C Macro Mode Setting • Macro mode cannot be used depending on the shooting mode. See “Default Settings” (A50) for more information. • The macro mode setting applied in A (auto) mode (A31) is saved in the camera’s memory even after the camera is turned off. Shooting Features 48 Basic Shooting Settings Adjusting Brightness (Exposure Compensation) Exposure compensation is used to alter exposure from the value suggested by the camera to make images brighter or darker. 1 Tap the exposure compensation icon. [ 930][930][ 930] 2 Tap or drag the slider to change the exposure compensation value. • To make the image brighter, apply positive (+) exposure compensation. • To make the image darker, apply negative (–) exposure compensation. Exposurecompensation 3 Press the shutter-release button to take an image. • To exit the setting screen without taking an image, tap I. • To cancel the exposure compensation, return to step 1, restore the value to [0], and tap I. Exposurecompensation00 +1.0+1.0+1.0-10.01.0-20.02 0 +20+2.0+2 0 Shooting Features C Exposure Compensation Value The exposure compensation value applied in A (auto) mode (A31) is stored in the camera’s memory even after the camera is turned off. 49 Basic Shooting Settings Default Settings The default settings for each function in each shooting mode are described below. • See the next page for information about the default settings in the scene modes. Flash mode (A44) Self-timer (A46) Macro mode (A48) Exposure compensation (A49) G (easy auto) a1 Off Off2 0.0 A (auto) a Off Off 0.0 R (special effects) a Off Off 0.0 F (smart portrait) a3 Off4 Off5 0.0 D (movie) – Off5 Off – 1 a (Auto) (default setting) or W (Off) can be selected. When a (Auto) is selected, the camera automatically selects the flash mode appropriate for the scene it has selected. 2 The setting cannot be changed. The camera enters macro mode when i is selected. 3 The function cannot be used when Blink proof is set to On. 4 The function...