Stimmen - 4, Durchschnittliche Bewertung: 4.3
(
)
)
|
Anleitung Zusammenfassung
When this happens, use daylight, cloudy, or one of the other fixed white balance settings to specify the type of lighting available. • You can use the key customization feature (page 120) to configure the camera so the white balance setting changes whenever you press [] or [] while in the REC mode. • If you have key customization configured to control white balance and you have Icon Help turned on (page 122), select “AWB Auto WB” to change the white balance mode to auto. Configuring the White Balance Setting Manually Certain complex light sources or other environmental conditions can make it impossible to obtain good results when “Auto” or one of the fixed light source settings is selected for white balance. Manual white balance lets you configure the camera for a particular light source and other conditions. Note that you must perform manual white balance under the same conditions you will be shooting under. Have a sheet of white paper on hand before starting the following procedure. 1. In the REC mode, press [MENU]. 2. Select a “Quality” tab, select “White Balance”, and then press []. 93 OTHER RECORDING FUNCTIONS 3. Use [] and [] to select “Manual”. • This causes the object you last used to adjust manual white balance to appear on the monitor screen. If you want to use the same settings you configured during a previous manual white balance setting operation, skip step 4 and perform step 5. 4. Point the camera at a white paper or similar object under the lighting conditions for which you want to set the white balance, and then press the shutter button. White paper • This starts the white balance adjustment procedure. The message “Complete” appears on the monitor screen after white balance adjustment is complete. 5. Press [SET]. • This registers the white balance settings and returns to the currently selected recording mode. NOTE • After you adjust white balance manually, the setting remains in effect until you change it or until you turn off the camera. 94 OTHER RECORDING FUNCTIONS Using Continuous Shutter You can configure the camera to record only a single snapshot each time the shutter button is pressed, or to keep recording as long as the shutter button remains depressed. You can select from among the following three continuous shutter modes. • Normal-speed continuous shutter You can continually record images until memory becomes full. • High-speed continuous shutter Record up to three consecutive images at high speed. • Flash continuous shutter Use this mode to record up to three consecutive images, firing the flash for each one. 1. In the REC mode, press [MENU]. 2. Select the “REC” tab, select “Continuous”, and then press []. 3. Use [] and [] to select “Normal Speed”, “High Speed”, or “Flash Cont. ”, and then press [SET]. • This causes the applicable icon to appear on the monitor screen. : Normal-speed continuous shutter : High-speed continuous shutter : Flash continuous shutter • With “Off”, snapshots are recorded one at a time. IMPORTANT! • Turning off the camera automatically turns off the continuous shutter mode. 95 OTHER RECORDING FUNCTIONS Normal-speed continuous shutter Holding down the shutter button continuously records images, as long as there is memory available to store them. Release the shutter button to stop recording. • You can select the flash mode you want with normal- speed continuous shutter (page 71). • The speed of continuous shutter recording depends on the type of memory card loaded in the camera. When recording to built-in memory, continuous shutter recording is relatively slow. High-speed continuous shutter Holding down the shutter button while high-speed continuous shutter is selected records up to three images at high speed. Shooting stops if you release the shutter button before three images are recorded. • Flash is turned off automatically. • Note that the resolution of images recorded with high- speed continuous shutter is somewhat lower resolution and more prone to digital noise than images recorded with normal-speed continuous shutter. • “Auto” ISO sensitivity always is used for high-speed continuous shutter, regardless of the current ISO sensitivity setting. Flash continuous shutter Holding down the shutter button while flash continuous shutter is selected records up to three images, firing the flash for each one. Shooting stops if you release the shutter button before three images are recorded. • Flash is turned on automatically. • Note that the resolution of images recorded with flash continuous shutter is somewhat lower resolution and more prone to digital noise than images recorded with normal-speed continuous shutter. • “Auto” ISO sensitivity always is used for flash continuous shutter, regardless of the current ISO sensitivity setting. • With flash continuous shutter, the flash range is narrower than normal. 96 OTHER RECORDING FUNCTIONS Using the BEST SHOT Mode Simply select one of a collection of built-in sample scenes and the camera sets up for the scene you s...