Stimmen - 4, Durchschnittliche Bewertung: 4
(
)
)
|
Anleitung Zusammenfassung
Each image that you select by pressing the shutter button will have a mark appended to it. 2After selecting all of the images you want to save, press [0] (Movie). 3Use [8] and [2] to select the save method you want and then press [SET]. Save All Saves all the images. Mark Buttons Used for Image Selection Save Selected : Saves selected images. Save All : Saves all the images. Cancel Save : Does not save any of the images. [4] [6] During playback, changes the playback direction and playback speed. While playback is paused, scrolls forward or back. [SET] Toggles between pause and play. Shutter button Press all the way down to select an image for saving. [0] (Movie) Saves the selected images and exits the image select operation. • Does not save any of the images while “Cancel Save” is selected. Snapshot Tutorial 44 IMPORTANT! • If there is not enough available capacity on the memory card, you may not be able to record the number of CS images indicated on the monitor screen. Make sure your memory card has sufficient remaining capacity before shooting with using continuous shutter. • With continuous shutter, exposure and focus for the first image are applied for successive images as well. • When using a continuous shutter mode, keep the camera still until shooting is finished. • Continuous shutter cannot be used in combination with any of the following. – Some BEST SHOT scenes – Make-up Mode, Landscape Mode • The speed of “CS: Normal Speed CS” depends on the type of memory card loaded in the camera and the amount of free space available for storage. When shooting to built-in memory, continuous shutter shooting is relatively slow. • “CS: Normal Speed CS” speed is slower when shooting with flash. • You cannot use the self-timer in combination with “CS: Normal Speed CS”, “CS: 4 fps”, “CS: 10 fps”. • Note that images recorded with “CS: 4 fps”, “CS: 10 fps” and “CS: Flash” are of somewhat lower resolution and more prone to digital noise than images recorded with “CS: Normal Speed CS”. • The ISO sensitivity setting always is “Auto” for “CS: 4 fps”, “CS: 10 fps” and “CS: Flash”, regardless of the camera’s current ISO sensitivity setting. • The flash range for Flash CS is narrower than that for normal flash. • Shooting a very bright subject can cause a vertical band or a pink cast on the monitor screen image. This does not indicate malfunction. Snapshot Tutorial 45 Using the Self timer (Self-timer)Using the Self timer (Self-timer) With the Self-timer, pressing the shutter button starts a timer. The shutter is released and the image is shot after a fixed amount of time. 1. In the REC mode, press [SET]. 2. Use [8] and [2] to select the sixth Control Panel option from the top (Self-timer). 3. Use [4] and [6] to select the setting you want and then press [SET]. 10sec Self-timer „ 10-second Self-timer 2sec Self-timer ‚ 2-second Self-timer • When shooting under conditions that slow down the shutter speed, you can use this setting to prevent image blur due to camera movement. X3 Self-timer (Triple Self-timer) ” Shoots three images: one image 10 seconds after the shutter button is pressed, and the next two images as soon as the camera is ready after shooting the previous image. How long it takes for the camera to get ready to shoot depends on the image size and quality settings, whether or not a memory card is loaded in the camera, and the flash charge condition. Self-timer Off Turns off the Self-timer. • The front lamp flashes while the Self-timer countdown is in progress. • You can interrupt an ongoing Self-timer countdown by pressing [SET]. NOTE Front lamp • The Self-timer cannot be used together with the following features. CS: Normal Speed CS/4fps/10fps, some BEST SHOT scenes • The Triple Self-timer cannot be used together with the following features. Auto Shutter, CS, Movie, Make-up Mode, Landscape Mode, some BEST SHOT scenes Snapshot Tutorial 46 Using Face Detection (Face Detection) Using Face Detection (Face Detection) When shooting people, the face detection feature detects the faces of up to ten individuals and adjusts focus and brightness accordingly. 1. In the REC mode, press [SET]. 2. Use [8] and [2] to select the third Control Panel option from the bottom (Face Detection). 3. Use [4] and [6] to select “G Face Detection: On” and then press [SET]. 4. Point the camera at the subject(s). The camera will detect human faces and display a frame around each one. 5. Half-press the shutter button. The camera will focus and the frames around the faces it focuses on will turn green. Face Detection icon 6. Press the shutter button the rest of the way down. IMPORTANT! • The camera performs center focus if it cannot detect a face. • The only focus mode available while face detection is enabled is Auto Focus (AF). • Face detection may take a bit longer when you hold the camera sideways. • Detection of the following types of faces is not supported. – Face that is obstructed by hair, sunglasses, a hat, etc., or a face in dark shade ...