Stimmen - 3, Durchschnittliche Bewertung: 4.3
(
)
)
|
Dieses Gerät hat auch andere Anweisungen:
Kameras - DSLR-A900 (3.53 mb)
Kameras - DSLR-A900 (6.3 mb)
Anleitung Zusammenfassung
When you rotate the camera to a vertical position, the display automatically rotates to adjust to the camera position. Detailed display Enlarged display DISP button No display • You can set the display so as not to be rotated with [Rec.info.disp.] in the Custom menu (page 120). Note Note You can display the screen used for adjusting the brightness of the LCD monitor by pressing the DISP button a little longer (page 127). Before your operation 43 Display panel Display panel A Shutter speed (54)/Aperture (53) Exposure (70) White balance (75) ISO sensitivity (74) Drive mode (83) B Display Indication Battery remaining (19) [100] Remaining number of recordable images (33)* * Even when the remaining number of recordable images is more than 999, “999” is displayed on the display panel. To turn on the backlight of the display panel Press the display panel illumination Display panel illumination button button on the top. Pressing again turns off the backlight. Viewfinder Viewfinder A Display Indication AF area (60) Spot AF area (60) Spot metering area (69) Shooting area for aspect ratio 16:9 (107) APS-C size area (134) Display Indication SteadyShot scale (46) Aspect ratio 16:9 (107) B Display Indication Flash compensation (73) Flash charging (65) WL Wireless flash (66) High-speed sync (67) Manual focus (62) z Focus (59) 125 Shutter speed (54) 5.6 Aperture (53) EV scale (55, 86) AE lock (71) 9 Shots-remaining counter (84) Camera shake warning (46) Before your operation 45 Camera shake warning indicator Due to potential camera shake, the (Camera shake warning) indicator flashes in the viewfinder. Note • The (Camera shake warning) indicator is displayed only in the exposure modes that the shutter speed is automatically set. This indicator is not displayed in M/S/PS modes. SteadyShot scale indicator Setting the switch to “ON” turns on the (SteadyShot scale) indicator. Wait until the camera shake is reduced and the scale becomes low, then start shooting. This SteadyShot function can reduce the effect of camera shake by the equivalent switch of approximately 2.5 to 4 increments of shutter speed. Note • The SteadyShot function may not work optimally when the power has just been turned on, just after you aim the camera, or when the shutter button has been pressed all the way down without stopping halfway. Wait for the (SteadyShot scale) indicator scale to go down, and then press the shutter button down slowly. Selecting a function/setting Selecting a function/setting When you start an operation, an operation guide that indicates a function of the multi-selector is displayed at the bottom of the screen. : To the left/right for selection : Up/down for selection : Up/down/to the left/to the right for selection z: Press the center button to execute the selection. Move the multi-selector by following the instructions in the operation guide to select an item. Operation guide The operation guide list The operation guide also indicates operations other than the multi-selector operation. The indications of icons are as follows. Display Indication MENU button Returns with MENU button button button Fn button Display Indication button Front or rear control dial Front control dial, rear control dial DISP button Returns with DISP button Before your operation 47 Selecting the functions on the Quick Navi screen Selecting the functions on the Quick Navi screen 1 Press the Fn button so that the Quick Navi screen appears. 2 Following the operation guide, select the desired item with v/V/ b/B on the multi-selector. Operation guide 3 Set the item with the front or rear Front control dial control dial. • For details on how to set up each item, see the corresponding page. • Pressing the Fn button again turns off the Quick Navi screen. Rear control dial • Gray items on the Quick Navi screen are not available. • When using Creative Style (page 80), some of the setup tasks can be accomplished only on the Exclusive disp screen. To set up a function on the Exclusive disp screen When the Quick Navi screen is displayed, pressing the center of the multi- selector turns on the Exclusive disp screen to set up the selected item. For details on how to set up each item, see the corresponding page. The “AUTO” mode allows you to easily shoot any subject under any conditions. 1 Set the mode dial to . 2 Hold the camera and look into the viewfinder. Shooting images Focus area Focus indicator 3 Press the shutter button halfway down to focus and press the shutter button fully down to shoot. When the focus is confirmed, the focus indicator z or (Focus indicator) lights up (page 59). Notes • If you turn the camera off or change the exposure mode in the AUTO mode, the main shooting functions are reset to the default settings. The functions that are not reset are as follows: – Switch, dial, buttons: The switch, the diopter-adjustment dial, the items set with the DISP button, and the C button – Recording menu: Image size, Aspect ratio, Quality, Exposure step, Memory – Cu...