Stimmen - 2, Durchschnittliche Bewertung: 4
(
)
)
|
Dieses Gerät hat auch andere Anweisungen:
Anleitung Zusammenfassung
If code “CiDDiDD” is displayed on the LCD screen, the selfdiagnosis display function is working (page 76). Should your camera still not work properly, press the RESET button on the bottom of the camera using a fine-tipped object, then turn on the power again. (All the settings including date and time are cleared.) RESET button U RESET 3 Should your camera still not work properly, consult your Sony dealer or local authorized Sony service facility. Batteries and power Symptom Cause Solution The battery remaining indicator is incorrect, or sufficient battery remaining indicator is displayed but the power runs out soon. • You have used the camera in an extremely cold location. • The batteries are discharged. • The battery contacts or the terminals on the battery/“Memory Stick Duo” cover are dirty. • The batteries are exhibiting the “memory effect” (page 11).^ • The batteries are dead (page 83). p Install charged batteries (page 10). p Wipe any dirt off from them with a dry cloth (page 11). p To restore the batteries to their original condition, use them until they are fully drained before recharging them. p Replace the batteries with new ones. The battery life is short. • You are shooting/viewing images in an extremely cold location. • The batteries are not charged enough. • The batteries are dead (page 83). p Charge the batteries (page 10). p Replace the batteries with new ones. lit 67 2 Troubleshooting Symptom Cause Solution You cannot turn on the camera. • The batteries are not installed correctly. • The batteries are discharged. • The batteries are dead (page 83). p Install the batteries correctly (page 12). p Replace them with charged batteries (page 10). p Replace the batteries with new ones. The power turns off suddenly. • If you do not operate the camera for about three minutes when using batteries, the camera turns off automatically to prevent wearing down the batteries (page 15). • The batteries are discharged. p Turn on the camera again (page 14). p Replace them with charged batteries (page 10). Shooting still images/movies Symptom Cause Solution The subject does not appear on the LCD screen. • The mode switch is set to [►]. p Set the mode switch to or |H| (pages 20 and 46). The image is out of focus. • The subject is too close. • When shooting still images, (Illumination snap mode), ^ (Twilight mode), (Vivid nature mode), or qj» (Active outdoor mode) is selected for the Scene Selection function. • You are shooting movies at a distance closer than 1.0 m (3 feet 3 3/8 inches). • The Focus preset function is selected. p Make sure to position the lens farther away from the subject than the minimum shooting distance of 10 cm (4 inches) when shooting (page 20). p Cancel the Scene Selection function (page 29). p Select the Focus preset function (page 30). p Set it to [AUTO] (page 31). The image is too dark. • The LCD screen is too dark. p Set [LCD LIGHT] to [ON] (pages 21 and 79). The image is too bright. • The LCD screen is too bright. p Set [LCD LIGHT] to [OFF] (pages 21 and 79). Vertical streaks appear when you are shooting a very bright subject. • The smear phenomenon is occurring. p This is not a malfunction. 68 Symptom Cause Solution Your camera cannot record images. • No “Memory Stick Duo” is inserted. • The capacity of the “Memory Stick Duo” is insufficient. • You are using a ‘Memory Stick Duo” with a write-protect switch, and the switch is set to LOCK. • You cannot shoot while the flash is charging. • The mode switch is not set to when shooting a still image. • The mode switch is not set to |H| when shooting a movie. p Insert a “Memory Stick Duo” (page 17). p Delete the images saved in the “Memory Stick Duo” (page 50), or format it (page 51). p Change the “Memory Stick Duo.” p Set it to the recording position (page 82). p Set it to Û (page 20). p Set it to U (page 46). The flash does not work. • The mode switch is set to [►] or |p|. • The flash is set to ® (No flash). • When shooting still images, either ^ (Twilight mode) or (V ivid nature mode) is selected for the Scene Selection function, or the camera is in Burst mode. p Set it to Û (page 20). p Set the flash to auto (no indicator), (Red-eye reduction) or % (Forced flash) (page 24). p Set it to other modes (pages 18 and 29). The eyes of the subject come out red. — p Set the flash mode to (Red-eye reduction) (page 24). The date and time are recorded incorrectly. • The date and time are not set correctly. p Set the correct date and time (page 15). Viewing images Symptom Cause Solution Your camera cannot play back images. • The mode switch is not set to [►!. • You have changed a folder or file name. • You cannot play back images processed on your computer. • The camera is in USB mode. p Set it to [►] (page 35). p See page 63. p Cancel the USB connection (pages 58 and 65). The image cannot be played back on a computer. — p See page 71. Troubleshooting Symptom Cause Solution Your camera cannot perform enlarged play...