Stimmen - 1, Durchschnittliche Bewertung: 4
(
)
)
|
Anleitung Zusammenfassung
Make sure the card is inserted properly and then play back again. [WRITE ERROR PLEASE CHECK THE CARD] Data writing error. Turn the camera off and remove the card. Then insert the card and turn the camera on again. This error may also indicate that the card is damaged. [MOTION RECORDING WAS CANCELLED DUE TO THE LIMITATION OF THE WRITING SPEED OF THE CARD] • When you set the [PICT.MODE] to [30fpsVGA] or [30fps16:9], we recommend using cards that offer 10 MB/second or higher speeds (shown on their packages and elsewhere) for best results. [A FOLDER CANNOT BE CREATED] A folder cannot be created because there are no remaining folder numbers that can be used. (P85) Save your data to your computer, then use this unit to reformat the card. (P83) If you execute [NO.RESET] in the [SETUP] menu after formatting, the folder number is reset to 100. (P22) [PICTURE IS DISPLAYED FOR 4:3 TV]/ [PICTURE IS DISPLAYED FOR 16:9 TV] • The video cable is connected to the camera. Press [MENU/SET] if you want to delete this message at once. • Select [TV ASPECT] in the [SETUP] menu to change the TV aspect. (P23) • This message also appears when the USB connection cable is connected to the camera only. In this case, connect the other end of the USB connection cable to a PC or a printer. (P84, 87) [PLEASE RE-CONNECT THE PRINTER.] This message appears if you change the mode dial to [ ] while the camera and the PC are connected. Set the camera to a mode other than [ ] mode, check that no data is being transferred and then connect to the printer again. ([ACCESS] appears on the LCD monitor of the camera while data is being transferred.) [USB MODE CHANGED. PLEASE REMOVE THE USB CABLE.] This message appears if you change the mode dial to a mode other than [ ] while the camera and the printer are connected. Set the mode dial to [ ] again and then disconnect the USB connection cable. If this happens during printing, stop printing and then disconnect the USB connection cable. VQT1C63 Others Troubleshooting If you put the menu back to the settings at the time of purchase, the conditions may be improved. Carry out the [RESET] in the setup menu. (P23) ¦ Batteries and power supply Conditions Causes The camera turns off immediately even when battery power is full. The remaining battery power may not be displayed accurately, and the camera may suddenly stop working, when the type of battery and the settings on [BATTERY TYPE] are not identical. However this is not a malfunction. Depending on the battery brand and the operating temperature, or if exhausted batteries are used, the remaining battery power may not be displayed accurately. Please check [BATTERY TYPE] (P21) in the [SETUP] menu. The remaining battery power is low even if new batteries are inserted. The camera will not turn Are the batteries inserted correctly? on. Use sufficiently charged batteries when using Ni-MH batteries. The picture is not displayed on the LCD monitor. Is the power save mode (P21) or economy mode (P22) activated? Press the shutter button halfway to deactivate these modes. Are the batteries exhausted? Replace them with batteries which have sufficient capacity. (When you use Ni-MH batteries, charge them.) The camera turns off soon after turning it on. • Are the batteries exhausted? Replace them with batteries which have sufficient capacity. (When you use Ni-MH batteries, charge them.) • If you leave the camera on, the battery will be exhausted. Turn the camera off frequently by using power save mode (P21) or economy mode (P22) etc. ¦ Shooting Conditions Causes The picture cannot be Is the mode dial correctly set? recorded. Is there any memory capacity left on the built-in memory or the card? Before recording, delete some pictures. (P35) The recorded pictures are pale. There is dirt on the lens. The picture can become whitish if there is dirt e.g. fingerprints on the lens. If the lens is dirty, turn on the camera, eject the lens barrel (P9) and gently wipe the lens surface with a soft dry cloth. The recorded picture is too bright or dark. Check that the exposure is correctly compensated. (P44) VQT1C63 Others Conditions Causes The subject is not focused properly. The focus range varies depending on the recording mode. To set the proper mode for the distance to the subject, rotate the mode dial. Is the subject out of the focus range? (P25, 46) Have you taken a picture with jitter? Sometimes two or three pictures are taken with a single press of the shutter button. Is the camera set in burst mode (P65)? The recorded picture When taking a picture in shaded areas or indoors, the shutter is blurred. The optical speed becomes slow and the Optical Image Stabilizer image stabilizer is not function may not work properly. In this case, we recommend effective. holding the camera with both hands firmly to take pictures (P25). Images are grainy or noisy. Is the ISO sensitivity high or the shutter speed slow? (When set to [AUTO], ISO sensitivity increases for indoor and other shooting occ...