Stimmen - 2, Durchschnittliche Bewertung: 3
(
)
)
|
Anleitung Zusammenfassung
• Using a Panasonic SD Memory Card (32 MB) • Starting recording 30 seconds after the camera is turned on. • Recording once every 30 seconds, with full flash every second recording. • Rotating the zoom lever from Tele to Wide or vice versa in every recording. • Turning the camera off every 10 recordings. Leaving the camera until the battery cools down. • CIPA is an abbreviation of [Camera & Imaging Products Association]. The number of recordable pictures varies depending on the recording interval time. If the recording interval time becomes longer, the number of recordable pictures decreases. (e.g. When recording once every 2 minutes: about 1/4 of the number when recording once every 30 seconds) Playback time Approx. 420 min The number of recordable pictures and playback time will vary depending on the operating conditions and storing condition of the battery. • Charging Charging time Approx. 130 min Charging time and number of recordable pictures with the optional battery pack (DMWBCF10PP) are the same as above. The charging time will vary slightly depending on the status of the battery and the conditions in the charging environment. When the charging has been completed successfully, the [CHARGE] indicator turns off. (ENG) VQT2B45 11 12 VQT2B45 (ENG) Inserting/Removing the Battery/Card (Optional) • Check that the camera is turned off. • We recommend using a Panasonic card. 1 Slide the release lever in the direction of the arrow and open the card/battery door. • Always use genuine Panasonic batteries (DMWBCF10PP). • If you use other batteries, we cannot guarantee the quality of this product. 2 Battery: Insert it fully being careful about the direction for insert. Pull the lever A in the direction of the arrow to remove the battery. Card: Push it fully until it clicks being careful about the direction for insert. To remove the card, push the card until it clicks, then pull the card out upright. B Do not touch the connection terminals of the card. • The card may be damaged if it is not fully inserted. 3 1: Close the card/battery door. 2: Slide the release lever in the direction of the arrow. • If the card/battery door cannot be completely closed, remove the card, check its direction and then insert it again. Note • The battery may swell and its operating time may become shorter as the number of times it is charged increases. For long term battery use, we recommend you do not frequently charge the battery before it is exhausted. • The performance of the battery may temporarily deteriorate and the operating time may become shorter in low temperature conditions (e.g. skiing/snowboarding). OFF ON ONOFF Setting Date/Time (Clock Set) • The clock is not set when the camera is shipped. 1 Turn the camera on. • When you turn the camera on, [PLEASE SET THE CLOCK] message appears. (It does not appear in Playback Mode.) A [MENU/SET] button B Cursor buttons A 2 Press [MENU/SET]. B 3 Press w/q to select the items (year, month, day, hour, minute, display sequence or time display format), and press e/r to set. C Time at the home area Cq D Time at the travel destination 4: Cancel without setting the clock. • Select either [24HRS] or [AM/PM] for the time display format. • AM/PM is displayed when [AM/PM] is selected. 4 Press [MENU/SET]. • After completing the clock settings, turn the camera off. Then turn the camera back on, switch to Recording Mode, and check that the display refl ects the settings that were performed. • When [MENU/SET] has been pressed to complete the settings without the clock having been set, set the clock correctly by following the “Changing the clock setting” procedure. Dw Changing the clock setting 1 Press [MENU/SET] in Normal Picture Mode. 2 Press e/r to select [CLOCK SET]. 3 Press q and perform steps 3 and 4 for setting. 4 Press [MENU/SET] to close the menu. • You can also set the clock in the [SETUP] menu. • The clock setting is maintained for 3 months using the built-in clock battery even without the battery. (Leave the charged battery in the unit for 24 hours to charge the built-in battery.) (ENG) VQT2B45 13 About the Mode and Menu Operation About the Mode and Menu Operation Mode switching 1 Slide the recording/playback switch A to 1 (right) or 5 (left). 1: Recording Mode 5: Playback Mode 2 Press [MODE] to display the mode selection screen. (Example: Normal Picture Mode) 3 Press e/r to select a mode and press [MENU/SET] to close the menu. • List of Recording Modes MODEMODE ; Auto Scene Mode Taking pictures easily. 1 Normal Picture Mode Taking pictures in the desired setting. 5 Scene Mode Taking pictures according to the scene. 6 Motion Picture Mode This mode allows you to record motion pictures with audio. • List of Playback Modes 9 Normal Play Mode Playing back the pictures normally. 8 Slide Show Mode Playing back the pictures continuously. z Favorite Play Mode Playing back the pictures set as your favorite. • Pictures do not appear when the [FAVORITE] is set to [OFF]. 14 VQT2B45 (ENG) About the menu...