Stimmen - 4, Durchschnittliche Bewertung: 3.8
(
)
)
|
Anleitung Zusammenfassung
Do not touch the power supply cord before disconnecting from the power supply. • Disconnect the appliance from the power supply when not in use, before fitting or removing parts and before cleaning. Safety of others • Do not allow children or any person unfamiliar with these instructions to use the appliance. • Do not allow children or animals to come near the work area or to touch the appliance or power supply cord. • Close supervision is necessary when the appliance is used near children. • This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been give supervision or instruction concerning use of the appliance by a person responsible for their safety • Children must be supervised to make sure that they do not play with the appliance. English -4- After use • Switch off and remove the plug from the socket before leaving the appliance unattended and before changing, cleaning or inspecting any parts of the appliance. • When not in use, the appliance should be stored in a dry place. Children should not have access to stored appliances. Inspection and repairs • Before use, check the appliance for damaged or defective parts. Check for breakage of parts, damage to switches and any other conditions that may affect its operation. • Do not use the appliance if any part is damaged or defective. • Have any damaged or defective parts repaired or replaced by an authorised repair agent. • Before use, check the power supply cord for signs of damage, ageing and wear. • Do not use the appliance if the power supply cord or mains plug is damaged or defective. • If the power supply cord or mains plug is damaged or defective it must be repaired by an authorised repair agent in order to avoid a hazard. Do not cut the power supply cord and do not attempt to repair it yourself. • Never attempt to remove or replace any parts other than those specified in this manual. Warning symbols The following symbols are used in this manual: Do not use this appliance near bathtubs, showers, basins or other vessels containing water. When the hairdryer is used in a bathroom, unplug it after use since the proximity of water presents a hazard even when the hair dryer is switched off. Denotes risk of personal injury or damage to the product in case of nonobservance of the instructions in this manual. Denotes risk of electric shock. Electrical safety This tool is double insulated in accordance with EN 60335; therefore no earth wire is required. Always check that the power supply corresponds to the voltage on the rating plate. To avoid the risk of electric shock, do not immerse the cord, plug or motor unit in water or other liquid. For additional protection, the installation of a Residual Current Device (RCD) having a rated residual operating current not exceeding 30mA is advisable in the electrical circuit supplying the bathroom. Ask your installer for advice. Features 1 Cool shot button 2 Heat control switch 3 Speed control switch 4 Hanging loop 5 Concentrator nozzle 6 Diffuser nozzle 7 Rear cover Following symbols are used on unit: 1 Cool shot: To help style the hair 2 Speeds: Off position Low speed High speed 3 Heat settings: Warm air Hot air Very hot air ! English -5- Assembly Warning! Make sure that the appliance is switched off and unplugged. Fitting and removing the attachments (Fig. A) • Allow the appliance to cool before changing the attachments. • Fit the diffuser nozzle (6) or the concentrator nozzle (5) by pushing it onto the outlet sleeve until it snaps into place. Removed the item by pulling it from the appliance. Use Warning! The appliance may be hot during use and during the cool-down period. Switching on and off (Fig. B) • The speed control switch (3) has three positions: off, slow and fast. • Move the switch to position 0 to switch the appliance off. • Turn the switch to position 1 for blowing air at a slow speed. • Turn the switch to position 2 for blowing air at a high speed. Heat control (Fig. B) • The heat control switch (2) has three positions: warm, hot and very hot. • Move the switch to position 1 for normal warm air. • Move the switch to position 2 for hot air. • Move the switch to position 3 for very hot air. Diffuser and concentrator nozzles • Fit the concentrator nozzle (5) for general hair drying and styling. • To add volume and lift, fit the diffuser nozzle (6). Cool shot button (Fig. B) • Press and hold the cool shot button (1) to set your individual style. Cleaning and maintenance Warning! Switch the appliance off and unplug it before cleaning or maintenance. • Remove any loose hair which may have become trapped in the diffuser or the rear filter. • Open the rear cover (7) and remove hair. • Do not try to disassemble or repair the hair dryer yourself. • Switch off the appliance before cleaning, changing accessories or touching any parts which move in use. Always clean the appliance immediately...