Stimmen - 4, Durchschnittliche Bewertung: 4.8
(
)
)
|
Anleitung Zusammenfassung
copied one) again. The other party complains that the «If your line has special telephone service such as letters on the document are distorted. call waiting, it may have been activated by another telephone call. Connect the unit to a line that does not have such service. •Be sure another telephone is not connected to the same line as your unit. The START/COPY indicator flashes for about 40 seconds after the unit receives a call automatically, but nothing is recorded. »The caller hangs up during or immediately after playing back your OGM. This may occur if the disconnect signal is not transmitted from the central office. When I receive or copy a document »This is quite normal, that has a dark background or contains photographs, the unit produces a high pitched noise. 7-3 The unit does not operate properly. »Turn the POWER switch off, then turn it on again. Problems when receiving «Shorten your OGM to 10 seconds or less, international facsimiles. «FAX RX SPEED may need to be set to 4800 bps. See page 6-3. Answering Device & Telephone PROBLEM CAUSE & REMEDY The unit does not work when any button is pressed. •Turn the POWER switch off, then turn it on again. The unit has been set to the •The tape is not installed properly or is broken TAD/FAX mode, but no (cut, worn out or twisted). Install the tape or voice-messages have been recorded. replace it with a new one. When the tape is played, the sound •Raise the sound level using the VOLUME level is low or nothing can be heard. control. •Clean the head of the cassette deck compartment. See page 7-6. I have played back all the recorded messages and I want to record the next call after the last message. •Leave the unit as it is after hearing the messages. I cannot retrieve recorded messages •Make sure that you use your REMOTE TAD ID from a remote phone. number correctly. •When you press your REMOTE TAD ID number, press the buttons firmly. Some voice-messages have not been •Set the calling party control (CPC) to “B”. See fully recorded. page 6-4. When a caller hangs up after leaving •VOX TIME should be set to 4 seconds. See page a message, the tape does not stop. 6-8. The unit does not ring. •Set the RINGER volume selector to the HIGH or LOW position. 7-4 Printer test You can check the print quality of your unit by printing the test pattern. If the test pattern has any blurred points or lines or a dirty pattern, consult with your service center. To obtain the test pattern, follow the steps below. “| Press the PROGRAM button. The PROGRAM indicator lights and the display shows “P-_”. 2 Press then press “42” for PRINTER TEST setting. The display shows “P-F42”. 3 Press the START/COPY button. The unit prints the pattern as shown in Figure 1. 4 Press the PROGRAM button to end the operation. The PROGRAM indicator goes out. Figure i Paper jams Document jams: Open the cover by pressing the BACK LID OPEN lever and clear the document that is causing problem. Recording paper jams: Open the cover by pressing the FRONT LID OPEN lever and remove the recording paper and re-install it properly. (See Recording paper installation on page 1-6.) 7-5 •Maintenance Be sure that the AC plug is disconnected from the outlet before performing any maintenance. - Cassette deck Since the head and capstan assemblies are in contact with the tape, dirt and residue from the tape may easily adhere to these parts, causing distortion. Clean these parts periodically in the manner described below for the best sound quality. Clean the head surfaces, pinch roller and capstan with a cotton swab. If these surfaces are extremely dirty, wipe them with a cotton swab dampened with alcohol, then wipe them with a dry soft cloth. Note: •Do not bring magnetic or metal objects, such as a screwdriver, near the head assembly, as such objects could magnetize the heads. •Do not oil any part of the unit. 7-6 Facsimile machine If a streak or a dirty pattern appears on a copied, transmitted or received document; 1. Clean the glass with a dry soft cloth. 2. Clean the paper rollers with a damp cloth then dry thoroughly to prevent the paper from jamming. If you cannot get a clear copy after performing the above steps 1 and 2, clean the thermal head with a cloth moistened with denatured alcohol (alcohol without water), then dry thoroughly. To prevent malfunction due to static electricity, do not use a dry cloth and do not touch the thermal head with your finger directly. 7-7 Specifications Type: Applicable Lines: Compatibility: Document Size: Effective Scanning Width: Printing Paper Size: Effective Printing Width: Transmission Time*: Scanning Density: Scanner Type: Printer Type: Data Compression System: Modem Speed: Automatic Document Feeder: Temperature Range: Humidity Range: Dimensions (HxWxD): Weight: Power Consumption: Power Supply: Desktop Public Switched Telephone Network CCITT G3 Max. 216 mm (8^") in width, Max. 600 mm (23^") in length Max. 208...