Stimmen - 1, Durchschnittliche Bewertung: 5
(
)
)
|
Anleitung Zusammenfassung
The AMPLIFY volume level complies with FCC standards. VOLUME AMPLIFY: OFF This default setting is appropriate if none of the users are hearing-impaired. During a conversation, users can press ^ or ^ on the control panel to adjust the volume to LOW or HIGH. When the handset is replaced, the handset volume will remain until you change it again. Initial Setup 4 - 4 VOLUME AMPLIFY: ON–TEMPORARY ^ ^ This setting is appropriate if some of the users are hearing-impaired. During a conversation, users can press or on the control panel to adjust the volume to LOW or HIGH. When the handset is replaced, the handset volume returns to the default setting of LOW. VOLUME AMPLIFY:ON–PERMANENT Choose VOL AMPLIFY: ON?–PERMANENT? if all of the users are hearing-impaired. During a conversation, users can press or on the control panel to adjust the volume to LOW or HIGH. When the handset is replaced, the handset volume returns to the default setting of amplify. ^ ^ When you press ^ ^ on the control panel to adjust the volume, the LCD shows the setting you are choosing. Each key press changes the volume to the next setting. It is important that you do not choose PERMANENT unless all users are hearing-impaired. Otherwise, the default setting of amplify may damage the hearing of some users. Setting Volume Amplify or Please carefully read Choosing the Handset Volume (For Volume Amplify) on page 4-4 before you do the following steps: 1 Press Menu/Set, 1, 4. 2 If none of the users are hearing-impaired, press ^ or Ў to select 4.VOLUME AMPLIFY VOL AMPLIFY:OFF?, and then press Menu/Set and go to Step 4. —OR— If some or all of the users are hearing-impaired, press ^ or Ў to select VOL AMPLIFY:ON?, and then press Menu/Set. 3 If all the users are hearing-impaired, press ^ or Ў to select PERMANENT?, and then press Menu/Set. —OR— If only some of the users are hearing-impaired, press ^ or Ў to select TEMPORARY, and then press Menu/Set. 4 Press Stop/Exit. 4 - 5 Initial Setup Setting the Ring Volume You can turn the ring off or you can select a ring volume level when your machine is idle (not being used). Press ^ or ^ to adjust the volume level. Every time you press these keys, the fax machine will ring so you can hear the active setting as the LCD shows it. The volume changes with each key press. The new setting will stay until you change it again. Setting Tone and Pulse dialing mode (Canada Only) 1 Press Menu/Set, 1, 6. 2 Press ^ or Ў to select PULSE 6.TONE/PULSE (or TONE). Press Menu/Set. 3 Press Stop/Exit. Setting up your area code (USA only) If you must dial the area code to call within your area code, do not enter this setting. 1 Press Menu/Set, 0, 4. 2 Use the dial pad to enter your area code, and then press Menu/Set. 4.CALLER ID AREA CODE:000 AREA CODE:908 3 Press Stop/Exit. Initial Setup 4 - 6 5 Setup Receive Basic receiving operations Choosing the Receive Mode There are four different Receive Modes for the fax machine. You can choose the mode that best suits your needs. LCD How it works When to use it FAX ONLY The fax machine For dedicated fax lines. (automatic automatically receive) answers every call as a fax. FAX/TEL* The fax machine Use this mode if you expect to (fax and controls the line and receive lots of fax messages and few telephone) automatically answers every call. If the call is a fax it will receive the fax. If the call is not a fax it will ring (pseudo/double ring) for you to pick up the call. telephone calls. You cannot have an answering machine on the same line, even if it is on a separate wall jack on the same line. You cannot use the telephone company’s Voice Mail in this mode. TAD:ANSWER The external Use this mode if you have connected MACH. answering device an external answering machine to (with an (TAD) automatically your machine. external answers every call. The TAD setting works only with an answering Voice messages external answering machine. Ring device) are stored on the external TAD. Fax messages are printed. Delay and F/T Ring Time do not work in this setting. MANUAL You control the Use this mode if you do not receive (manual phone line and many fax messages, with Distinctive receive) must answer every call yourself. Ring or if you are using a computer on the same line. If you answer and hear fax tones, wait until the machine takes over the call, then hang up. (See Easy Receive on page 5-3) *In FAX/TEL mode you must set the RING DELAY and F/T RING TIME. If you have extension phones on the line, keep the RING DELAY set to 4 rings. 5 - 1 Setup Receive Current Receive Mode 09/06 15:25 FAX MAN:MANUAL FAX: FAX ONLY F/T: FAX/TEL TAD: ANSWER MACH. To select or change your Receive Mode 1 Press Receive Mode. The LCD shows your current selection. 2 Continue to press Receive Mode until your new selection appears. After 2 seconds, the screen returns to the date and time display, along with your new Receive Mode setting. FAX ONLY FAX/TEL TAD:ANSWER MACH. MANUAL If you are changing the Receive Mode while in another oper...