Stimmen - 2, Durchschnittliche Bewertung: 4.5 ( )

Hersteller: Philips Dateigröße: 3.88 mb Dateiname: ppf675e_frb_dfu_eng.pdf Unterrichtssprache:

The blue gear wheel must be on the right hand side. 8 Place the smaller roll without ink film in the front tray. The blue gear wheel must be on the right hand side and the pin must be inserted in the depression on the left hand side. 9 Break the chip card from the Plug’n’Print card. Insert the chip card in the plug socket on the left hand side next to the ink film tray. 10 Turn the blue gear wheel forward to tension the ink film. The ink film must not have any creases. 11 Close the device. Insert the paper tray in the opening provided for it behind the paper feeder. Insert paper again. Fixing a Paper Jam 1 Remove the paper from the paper feeder and take the paper tray out of the device. 2 Open the device by lifting the panel using grip in the centre and folding it up. 3 Carefully pull the paper out. 4 Turn the blue gear wheel forward to tension the ink film. The ink film must not have any creases. 5 Close the device. Insert the paper tray in the opening provided for it behind the paper feeder. Insert paper again. Lock the cover of the device completely into place when opening the device. You could be injured if the cover falls while you are working on the device. 30 Philips PPF 631 · 632 · 675 EN Fixing a Document Jam 1 Remove the paper from the paper feeder and take the paper tray out of the device. 2 Open the device by lifting the panel using grip in the centre and folding it up. 3 Open the scanner cover and the cover of the automatic document cover by first pushing the support (A) and then the support (B) inside. The cover (C) folds below. 4 Carefully pull the document to the front or to the back out of the device. 5 Close the scanner cover and the cover of the automatic document feeder. Both the supports must securely snap into place. 6 Turn the blue gear wheel forward to tension the ink film. The ink film must not have any creases. 7 Close the device. Insert the paper tray in the opening provided for it behind the paper feeder. Insert paper again. Cleaning Cleaning Fax Cleaning Sheets 1 Remove the paper from the paper feeder and take the paper tray out of the device. 2 Open the device by lifting the panel using grip in the centre and folding it up. Lock the cover of the device completely into place when opening the device. You could be injured if the cover falls while you are working on the device. Unplug the device from the power socket before cleaning it. Use a soft, lint-free cloth. Never use liquid or easily flammable cleansers (sprays, abrasives, polishes, alcohol, etc.). Do not allow any moisture to reach the interior of the device. Special fax cleaning sheets are available as accessories from our call centre. Insert a sheet into the document feeder. Press STOP; the page is ejected. Repeat this process at a few times. Lock the cover of the device completely into place when opening the device. You could be injured if the cover falls while you are working on the device. Service 31 EN 3 Open the scanner cover and the cover of the automatic document cover by first pushing the support (A) and then the support (B) inside. The cover (C) folds below. 4 Lightly wipe the upper side of the scanner glass (A) and the lower side of the document feeder/scanner film (= white plastic plate) (B) with a cloth. 5 Clean the feed roller (A) and the underside of the support pad of the feeder roller (B) with a soft, lint-free cloth moistened with cleaning alcohol (96 percent). Rotate the feed roller; You must clean the entire roller. 6 Close the scanner cover and the cover of the automatic document feeder. Both the supports must securely snap into place. 7 Turn the blue gear wheel forward to tension the ink film. The ink film must not have any creases. 8 Close the device. Insert the paper tray in the opening provided for it behind the paper feeder. Insert paper again. Checking the Firmware Version 1 Press OK, 47 and OK. 2 The model designation and the configured country appear on the display. 3 Confirm with OK. 4 The information on the firmware version of the device is displayed. 5 Confirm with OK. Using Service Codes The service codes delete all the changed settings and your device is reset to factory settings. It may be possible that the device with the changed settings reacts differently than expected. Using Service Codes 1 Press OK, 45 and OK. 2 Enter a service code: 7117—Deletes all changed settings and saved data. The device is reset to factory settings and the initial installation process is started. 7140—Deletes all changed settings. Saved data and telephone book entries remain intact. 7227—Deletes saved faxes, when there are problems with printing. 3 Confirm with OK. 4 Using [ select SURE: YES. 5 Confirm with OK. Only use the service codes if this is absolutely necessary. Some service codes also delete saved messages and telephone book entries. If you have entered the incorrect code, you can cancel the entry with SURE: NO. EN EN Power Cycling If a problem occurs that cannot be corrected with the instructions in...

Herunterladen

Geben Sie zwei Ziffern: