Stimmen - 3, Durchschnittliche Bewertung: 4
(
)
)
|
Anleitung Zusammenfassung
In typical use, alkaline batteries will last up to three years. 2. Install 3 alkaline "D" batteries. Make sure batteries are oriented properly. 1. Install alkaline type A23 12 volt push button battery. Remove back of case by pushing in tab on bottom with a small screwdriver. Make sure battery is oriented properly (see page 3). 3. Test range. Temporarily position chime and push button where you want them mounted. Press push button to verify chime and push button work properly. If chime does not sound, see Troubleshooting. 4. Mount push button and chime. Use either screws or double sided tape to mount push button. To mount with screws, remove back of case by pushing tab on bottom with a small screwdriver. Attach back of case to door jamb or wall. Snap front of button on. When attaching push button using double sided tape, See page 2 for help removing the chime case. make sure the surface of the door jamb or wall is clean. © 2007 HeathCo LLC 598-1000-06 The chime can be mounted vertically or horizontally (depending on model) using 2 holes in back of case, or using one keyhole and one mounting hole. It is highly recommended to use at least two mounting screws with anchors. It is recommended to secure chime to wall using screws and Pry with a small screwdriver to Keyholes anchors through both holes. remove case before installing. To remove cover after base is mounted, firmly grasp cover Snap cover onto and pull. chime as shown. Note: Model SL-6250 is packaged as a set. Mount shelf using keyholes on rear of unit and 2 large screws provided. Warning: Model SL-6250 may be used as a shelf and has a load rating of 5 lbs. (2.25 kg). All other chimes are not load rated. Code and Tune Settings Code Settings Note: Most installations will not require you to change any jumpers on your chime and push button. The push button and chime communicate by using a code that can be changed by removing and/or adding jumpers on both the push button and chime. The code is factory set; however, there are 128 selectable codes that allow you to expand your system and prevent outside interference. Other wireless products may cause interference and the system may not function properly. Follow the instructions below for setting a new code. 1. Open the cases and locate the jumpers on both the push button and chime (See illustration on page 3). 2. The push button and chime both have eight different jumper locations. The jumper positions 1 through 7 are used for setting the code. 3. To change the code, add and/or remove jumpers as needed. It is recommended to only change one jumper at a time and then check to see if system is functioning properly.Note: Jumpers in positions 1 through 7 must be exactly the same for both the push button and chime for this system to function. -2-598-1000-06 Tune Settings Your Heath®/Zenith wireless chime has different selectable tunes: Ding (one note), Ding-Dong (two note), or Westminster (eight note) (Available on selected Heath®/Zenith chimes). The factory setting is for the Ding-Dong tune (or Westminster, when available). This tune can be changed by following the instructions below. • Ding (one note tune) Push Button: Add a jumper to location 8. • Ding-Dong (two note tune) Push Button: Remove jumper from location 8. Chime: Remove jumper from location 8. • Westminster (Eight note tune) (Available on selected Heath®/Zenith chimes) Push Button: Remove jumper from location 8. Chime: Add a jumper to location 8. Note: All models have both front and back door tune capabilities. You may purchase any Heath®/Zenith wireless push button for a second entrance. We recommend the back door use the Ding tune and the front door use the Ding- Dong tune (or Westminster tune, available on selected Heath®/Zenith chimes). Models that include two push buttons will come factory set for front and back doors. Decals on the rear of the push button will indicate its setting. Push Button Battery Replacement Install an alkaline type A23 12Volt battery. See diagram Chime Volume inside push button for correct battery orientation. Control Inside Chime Tune Setting (Not used on all models) Note: Some models might require the use of tweezers to remove and replace the jumpers. 1 2 345 678 * Code Settings 1-7 Must Match Both Push Button and Chime Tune Setting Inside Push Button 12 345 678 598-1000-06 -3 Troubleshooting Chime does not sound: • Make sure push button and chime codes are the same (See pages 2 and 3). • Check orientation of push button battery (See page 3). • Check charge of push button and chime batteries, replace if necessary. Batteries seem OK, but the chime does not work when installed: • Do not mount chime or push button on metal or near metal studs. This reduces the transmitter range. Use 1/4" to 1/2" (6 to 13 mm) wood shims to move chime or push button off metal surface. • Concrete floors may reduce range. Move chime away from floor. • Try locating chime closer to push button. The range of the wireless chime can vary with locatio...