Stimmen - 1, Durchschnittliche Bewertung: 4
(
)
)
|
Anleitung Zusammenfassung
It is recommended to only change one jumper at a time and then check to see if system is functioning properly. Note: Jumpers in positions 1 through 7 must be exactly the same for both the transmitter and chime for this system to function. -4-595-5345-06 Tune Settings Your Heath®/Zenith wireless chime has different selectable tunes: Ding (one note), Ding-Dong (two note), or Westminster (eight note) (Available on selected Heath®/Zenith chimes). The factory setting is for the Ding-Dong tune (or Westminster, when available). This tune can be changed by following the instructions below. • Ding (one note tune) Transmitter: Add a jumper to location 8. • Ding-Dong (two note tune) Transmitter: Remove jumper from location 8. Chime: Remove jumper from location 8. • Westminster (Eight note tune) (Available on selected Heath®/Zenith chimes) Transmitter: Remove jumper from location 8. Chime: Add a jumper to location 8. Note: All models have both front and back door tune capabilities. You may purchase any Heath®/Zenith wireless push button for a second entrance. Remove screw to Transmitter Battery Replacement open access door Install four alkaline AAA batteries. See diagram inside push button for correct battery orientation. Back of Chime 12345678 * Code Settings 1-7 Must Match Both Transmitter and Chime Tune Setting Tune Setting Inside (Not used on Transmitter all models) Note: Some models might require the use of tweezers to remove and replace the jumpers. 12345678 595-5345-06 -5 Troubleshooting Chime does not sound: • Red light on the transmitter does not light. Check polarity of batteries. Replace the transmitter batteries. • Red light on the transmitter does light. Make sure the transmitter and the chime channels are the same (see page 5). Make sure the plug-in chime has power going to it. Battery seems OK, but the chime does not work when installed: • Do not mount the transmitter on metal or near metal studs. This reduces the transmitter range. Use 1/4" to 1/2" (6 to 13 mm) wood shims to move the transmitter off the metal surface. • Attach the microphone directly to the existing chime case very near the ringing part (but not on it) of the existing chime. •Try locating chime closer to transmitter. The range of the chime can vary with location, temperature, and battery condition. Chime false triggers to loud noises: The Extension Transmitter has special circuitry to reduce false triggers from most common household noises. The transmitter is designed to optimize its response to mid-frequency sound where most mechanical doorbells operate and to minimize response to extremely low or high frequency sounds. Also, the desired sound must be present continuously for at least 2 seconds. This design reduces the response to door slams, vibration, normal music and talking, etc. Loud continuous noises such as yelling children or very loud music may cause false triggering. When operating in a location with unusually high ambient noise levels try the remedies below. •Turn the sensitivity control counterclockwise to reduce sensitivity. • Mount the microphone inside the existing chime as mentioned in step 4. -6-595-5345-06 Technical Service (Do Not Send Products) If you experience a problem, follow this guide. You may also want to visit our Web site at: If the problem persists, call* for assistance at 1800- 858-8501, 7:30 AM to 4:30 PM CST (M-F). You may also write* to: DESA Specialty Products™ P.O. Box 90004, Bowling Green, KY 42102-9004 ATTN: Technical Service Specialty Products * If contacting Technical Service, please have the following information available: Model Number, Date of Purchase, and Place of Purchase. No Service Parts Available for this Product Regulatory Information This device (SL-6166-RX-A, SL-6157-A-TX) complies with Part 15 of the FCC Rules and RSS-210 of Industry Canada. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. The user is cautioned that changes or modifications not expressly approved by the party responsible for regulatory compliance could void the user’s authority to operate the equipment. 595-5345-06 -7 FIVE YEAR LIMITED WARRANTY This is a "Limited Warranty" which gives you specific legal rights. You may also have other rights which vary from state to state or province to province. For a period of five years from the date of purchase, any malfunction caused by factory defective parts or workmanship will be corrected at no charge to you. Batteries are not covered. To obtain a refund or a replacement, return the product to the place of purchase. Not Covered -Repair service, adjustment and calibration due to misuse, abuse or negligence, light bulbs and other expendable items are not covered by this warranty. Unauthorized service or modification of the product or of any furnished component will void this warranty in ...