Stimmen - 3, Durchschnittliche Bewertung: 3.7 ( )

Hersteller: BEA Dateigröße: 141.72 kb Dateiname: 940a0945-071c-40d7-a6d5-fbd10c7dbb04.pdf Unterrichtssprache:

These boxes are made of durable ABS plastic and are made to securely mount a pushplate and a variety of optional transmitters to activate an automatic door. Many of the boxes have an optional weather ring to give even more weather protection to the switch. They are also designed to attractively recess the pushplate in the housing to and to minimize vandalism from prying up the pushplate. PRODUCT DESCRIPTION COMPONENT ID PUSHPLATE SIZE PUSHPLATE SERIES SURFACE MOUNT BOX FLUSH MOUNT BOX WEATHER RING (Optional) Jamb (4” hole spacing) 10PBJx 10B0XJAMBSM 10B0XJAMBFM N/A Jamb (3 %” hole spacing) 10PBJSx 10B0XJAMBST N/A N/A 4 %” Square 10PBS45x 10B0X45SQSM N/A N/A 4 %” Square 10PBSx 10B0X475SQSM 10B0X475SQFM 10WRSQ475 4 %” Round 10PBR45x 10B0X45RNDSM 10B0X45RNDFM 10WRRND45 6” Round 10PBRX 10BOX6RNDSM 10BOX6RNDFM 10WRRND6 4” 3 % ” 4 /” 4 3/4 ” 4 / ” 6’ JAMB JAMB SQUARE SQUARE ROUND ROUND • Shut off all power going to the header before attempting any wiring procedures. • Maintain a clean & safe environment when working in public areas. • Constantly be aware of pedestrian traffic around the door area. • Always stop pedestrian traffic through the doorway when performing tests that may result in unexpected reactions by the door. • Always check placement of all wiring before powering up to insure that moving door parts will not catch any wires and cause damage to equipment. • Ensure compliance with all applicable safety standards (i.e. ANSI A156.10) upon completion of installation. SAFETY PRECAUTIONS 75.0092 V4 Jan 2004 [Rev. 1/26/2004] Page 1 of 2 MECHANICAL INSTALLATION COMPANY CONTACT 1. Prepare the box for installation. If the pushplate is to be hard-wired to the operator, remove either the knockout on the back or bottom of the box. Then route the appropriate wire to the box. 2. Attach the box to the mounting surface. For surface mounted boxes, securely attach the box to the surface using the corner holes. For flush mounted boxes, cut a hole in the mounting surface large enough that the galvanized steel bracket will pass through the hole. Then use a Phillips head screwdriver to tighten the two screws that tighten the bracket to the inside of the wall surface. GALVANIZED MOUNTING BRACKET SURFACE MOUNT FLUSH MOUNT If applicable, mount a radio frequency transmitter to the inside of the housing using either the transmitter pins and 9V battery clip, or the Velcro tab enclosed with the transmitter kit. Transmitter Mounting Pins (adjust location for transmitter) or use Velcro tab to secure ‘mini' transmitters 9V Battery 10BOX45RSM with 10T300PB shown If after troubleshooting a problem, a satisfactory solution cannot be achieved, please call B.E.A., Inc. for further assistance during Eastern Standard Time at 1-800-523-2462 from 8am - 5pm. For after-hours, call East Coast: 1-866-836-1863 or 1-800-407-4545 / Mid-West: 1-888-308-8843 / West Coast: 1-888-419-2564. DO NOT leave any problem unresolved. If you must wait for the foll...

Herunterladen

Geben Sie zwei Ziffern: