Stimmen - 2, Durchschnittliche Bewertung: 4
(
)
)
|
Anleitung Zusammenfassung
safety goggles) when drilling holes, etc. • Before drilling holes in walls, check for hidden electricity cables and water pipes. The use of a cable/pipe locator is advisable if in doubt. RCWL2205 69-2110EFS—01 1. Fit batteries. Push batteries (2 x AAA) not included. Chime batteries 3x C cell, not included. 2. Choose a code between 1 & 16. Apply the same code for push and chime. 150 FT MAX50 M MAX 3. Test your Chime and push. 4. Volume Control - Push button. 5. Selecting your standard tune. Switch A Position Switch B at Position 2 Switch B at Position 1 3 Plays list of pre- recorded songs one after the other. Plays the same selected tune. 2 Westminster 8 note Westminster 8 note 1 Ding Dong Dong Ding Dong Dong To change your tune Switch B to position 2 Play through your list of tunes by pressing the push until desired tune is reached, then… Switch B to position 1 this selects the desired tune. Switch B Switch A 6. Playing tunes from pre-recorded sound card: Fit the pre-recorded sound card into your Chime. 7. See the table below for tune selection. Switch A Position Switch B at Position 2 Switch B at Position 1 3 Plays list of pre-recorded songs one after the other. Plays the same selected tune. 2 Westminster 8 note Westminster 8 note 1 Ding Dong Dong Ding Dong Dong 8. Mounting your Chime and Push Drill two 1/4-in. (5 mm) fixing holes for mounting the push back plate. Do not mount on or next to a metal surface. 150 FT MAX50 M MAX Dense walls and metal can reduce range, before final installation adjust distance and position between push and chime while operating the push to optimize the chime within your environment. Wall Type Range Reduction Dry-lined partition wall 10–30% Single-layer brick wall 20–40% Double-layer brick wall 30–70% Metal panel/radiator 90–100% Troubleshooting “My Chime does not work…” Make sure the batteries are fitted correctly + / - polarity. Replace batteries every 12-18 months. Only use alkaline batteries. Make sure push and Chime are within range, see section 8 Check that the dial code on the bell push and chime are set at the same position. See section 2. Chime does not play tune selected: Ensure you have selected the right options – see section 5-6. Support website link: - with automatic updates. Disposal and Recycling At the end of their useful life the packaging and product should be disposed of via a suitable Recycling Center. Do not dispose of as normal household waste. DO NOT BURN. Check with your local authority or retailer for recycling advice. Declaration Honeywell hereby declares that this product complies with Part 15 of the FCC rules and Industrial Canada standards. This device operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. Caution: Changes or modification not expressly approved by the party responsible for regulatory compliance could void the user’s authority to operate the equipment. Guarantee Honeywell guarantees this product for 1 year from the date of purchase. Proof of purchase is required: this does not affect your statutory rights. If you require further information about your product call the Honeywell help line at 1-800-468-1502. Honeywell International Inc. ACS, Environmental and Combustion Controls 1985 Douglas Drive, Golden Valley, MN 55422 Printed in U.S.A. on recycled paper containing at least 10% post-consumer paper fibers. ® U.S. Registered Trademark. © 2007 Honeywell International Inc. 69-2110EFS—01 M.S. 11-07 Directives d’installation COMPARTIMENTA PILES CCOMPARTIMENTA PILES ACOMPARTIMENTA PILES BFENTE ENFORME DE POIREREGLAGE DU VOLUMECADRAN POUR CODEOUVERTURES DE FIXATIONFENTE POURCARTE DE SON USB Securite Avant de commencer l’installation, veuillez respecter les consignes de securite suivantes : • Toujours suivre les recommandations du fabricant lorsqu’on utilise des appareils electriques et toujours se servir d’un equipement protecteur (par ex. des lunettes de protection) lorsqu’on perce des trous, etc. • Avant de percer un trou dans un mur, verifier qu’il n’y a pas de canalisations ou de cables electriques encastres. En cas de doute, il est conseille d’utiliser un appareil permettant de detecter les cables/tuyaux. 1. Inserer les piles - Piles (2 x AAA) pour sonnette non comprises. Piles pour carillons non comprises (3 piles de taille C). 2. Choisir un code entre 1 et 16. Appliquer le meme code a la sonnette et au carillon. 50 M MAX150 PI MAX 3. Verifier la sonnette et le carillon. 4. Reglage du volume - Bouton-poussoir. 5. Selection d’une melodie standard. Position de l’interrupteur A Interrupteur B a la position 2 Interrupteur B a la position 1 3 Fait entendre une liste de melodies pre-enregistrees l’une apres l’autre. Fait entendre la meme melodie choisie. 2 Westminster, 8 notes Westminster, 8 notes 1 Ding Dong Dong Ding Dong Do...