Stimmen - 2, Durchschnittliche Bewertung: 4.5
(
)
)
|
Anleitung Zusammenfassung
When the alarm is allowed to arm passively, at the end of the 30 second arming cycle, the doors will notwill notwill notwill notwill not automatically lock. The system is shipped in the active door lock mode, therefore, no modifications are required for this feature. When passive door lock is selected, when the system is allowed to arm passively, at the end of the 30 second arming cycle, the doors willwillwillwillwill automatically lock. To program this feature, move dip switch number 1 to the on position. AUTO LOCK / UNLOCK: DIP SWITCH #2 The system is shipped with this feature activated. Any time the ignition key is turned to the off position, the doors will automatically unlock. Any time the ignition key is turned to the on position, the doors will automatically lock when doors are closed. To disable the auto lock / unlock feature, move dip switch number 2 to the “off” position. PASSIVE / ACTIVE ARMING SELECTION: DIP SWITCH #3 This alarm can be programmed to operate as either a “PASSIVE” or “ACTIVE” arming security system. As a “Passive” alarm, the system will automatically arm itself approximately 30 seconds after the ignition key is turned off, one door is opened, then all vehicle doors are closed, (arming is suspended until the last door is closed). This feature protects the vehicle in the event you forget to arm the system using the keychain transmitter. The doors will operate according to the position of dip switch number 1. This system is shipped in the passive mode, therefore no modifications are required to make the system operate as a “Passive” alarm. As an “Active” alarm, the system can only be armed using the keychain transmitter. There will be no backup automatic arming. To make the system operate as an “Active” alarm, move dip switch number 3 to the off position. INOPERATIVE: DIP SWITCH #4 CHANNEL 2 OUTPUT: This system provides an on board 10 A relay to activate the factory installed trunk release solenoid. CHANNEL 3 OUTPUT: This system provides an additional hardwire remote output to control an assortment of optional upgrades. This output is an independent channel from the transmitter, and is controlled by pressing both buttons on the transmitter simultaneously. It is a low current ground pulse (300 mA maximum), and the duration or length of the pulse varies (this output will provide a ground signal for as long as both buttons are held), making it a versatile feature. This output can be used to control; * Optional Remote Starter AS 9075 * Optional Window Roll Up AS 9153 Model PRO 9246FT Installation Manual PRE-INSTALLATION NOTES: PASSIVE / ACTIVE DOOR LOCK SELECTION: DIP SWITCH #1 This feature will only affect the operation of the system if the passive arming feature is selected. When active door lock is selected, the doors will only lock when the transmitter button is pressed. When the alarm is allowed to arm passively, at the end of the 30 second arming cycle, the doors will notwill notwill notwill notwill not automatically lock. The system is shipped in the active door lock mode, therefore, no modifications are required for this feature. When passive door lock is selected, when the system is allowed to arm passively, at the end of the 30 second arming cycle, the doors willwillwillwillwill automatically lock. To program this feature, move dip switch number 1 to the on position. AUTO LOCK / UNLOCK: DIP SWITCH #2 The system is shipped with this feature activated. Any time the ignition key is turned to the off position, the doors will automatically unlock. Any time the ignition key is turned to the on position, the doors will automatically lock when doors are closed. To disable the auto lock / unlock feature, move dip switch number 2 to the “off” position. PASSIVE / ACTIVE ARMING SELECTION: DIP SWITCH #3 This alarm can be programmed to operate as either a “PASSIVE” or “ACTIVE” arming security system. As a “Passive” alarm, the system will automatically arm itself approximately 30 seconds after the ignition key is turned off, one door is opened, then all vehicle doors are closed, (arming is suspended until the last door is closed). This feature protects the vehicle in the event you forget to arm the system using the keychain transmitter. The doors will operate according to the position of dip switch number 1. This system is shipped in the passive mode, therefore no modifications are required to make the system operate as a “Passive” alarm. As an “Active” alarm, the system can only be armed using the keychain transmitter. There will be no backup automatic arming. To make the system operate as an “Active” alarm, move dip switch number 3 to the off position. INOPERATIVE: DIP SWITCH #4 CHANNEL 2 OUTPUT: This system provides an on board 10 A relay to activate the factory installed trunk release solenoid. CHANNEL 3 OUTPUT: This system provides an additional hardwire remote output to control an assortment of optional upgrades. This output is an independent channel from the transmitter, and is control...
Dieses Handbuch ist für folgende Modelle:Haustüren und Fenster - PRO 9246FT (48.35 kb)