Stimmen - 1, Durchschnittliche Bewertung: 5
(
)
)
|
Anleitung Zusammenfassung
Allows up to 99 PIN codes .. Random user codes for anti-peeping .. Fully Programmable via keypad and master code .. LED display with audible indication .. Non-Volatile Memory .. Invalid PIN Lock-out .. Metal die casting housing .. Deftly dimension for narrow jamb .. With vandal resistant screws .. Split of controller and reader for high security. 2. Specifications: .. Operating Voltage: 12 Vdc .. Current Draw: Average 15mA, Peak 70mA @ 12Vdc .. Output: N.O./N.C./Com. Output (free voltage contact) .. Relays Rated: 2A MAX @30Vdc ;0.4A @ 120Vac .. Relay Activation Time: (*100) .. Strike Time: 1~99 seconds(adjustable) .. Strike mode: Access Timer or Latch .. PIN codes: 5 digit codes .. User codes capacity: 99 slots .. Operating Temperature: -20~+70. .. Ambient Humidity: 5~95% relative humidity non-condensing .. Factory Master Code: 12345 .. Invalid PIN Lock-out: The system will shut down for 60 seconds while 30 codes of incorrectly Master Codes enrolled or PIN codes attempted(None beeper signal of keypad activations). .. EPROM: Non-volatile memory, System will retain all programs and codes after a total loss of power. .. Color: Beige White .. Distance between the keypad and controller board: Maximum 50 M (cable#22~26 AWG). 3. The indicator signal chart: Sound and LED indicator: LED signal Green LED Relay activated Red LED Power on, stand-by Yellow LED Programming mode Sound signal 1 Beep Key-in, Effective PIN codes 2 Beeps Entering .Exiting from the Program mode 3 Beeps Data computing error . other operation mistakes 5 Beeps Master Code reset to Factory (12345)or remove all stored user codes 4. Default Setting: Master code 12345 Relay time 5 Pressed key delay 30 seconds Setting mode delay time 50 seconds 5. Operation Instruction: .. Enter Program Mode: 1. Compose twice the master code (Factory master is .12345.) > 2 beeps > you are now in the "programming mode". 2. After 50 seconds if you have not entered any codes or data, the system will automatically exit from the programming mode. 3. After 30 wrong codes attempts at the master code the lockout facility will operate. .. Exiting from the program mode: 1. Press.#. to exit from the programming mode. 2. After 50 seconds if you have not entered any codes or data, the system will automatically exit from the programming mode. 3. After 30 wrong codes attempts at the master code the lockout facility will operate. .. Add PIN codes Enter the Programming mode, Enter the slot position code .*001~*099.>????? Input 5 digit PIN codes> (beep) enrolled ..(repeat) Press .#. to exit from the programming mode, or program other operating. Note 1: The codes.00000.,.12345.or master code are not be used for PIN code. Note 2: Random user codes operate open door:.???????????????????????? ** ***.,.???…..random codes,.*****.5 digit user codes. (Random codes and correct user codes total 29 digits.) .. To Delete a User Code: Enter the Programming mode> Press the slot position code of your choice to delete (example "06") >Press.*006.>.00000.>(beep)>delete>Press.#. to exit from the programming mode, or programming other operating. .. To Program Relocking Timer Enter the Programming mode, A. Relay:Press.*100.Followed by the number of seconds the relay should open>.05.=5 seconds(01 ~99 = seconds)>(beep)>enrolled > Press .#. to exit from the programming mode, or program other operating. B. Enter.00.Sets the relay to latching mode. (Correct code entered opens the relay, and the relay stays open until the correct code is entered again). .. Changing the Master codes: Enter the Programming mode, Enter.*000.Followed by the new 5 digit master code>(beep)>enrolled>Enter .#. to exit from the programming mode, or program other operating. .. Master Code reset to Factory .12345. Insert the jumper RESET.. 1-2 position..5 audible beeps..Reset successful.. Return Insert the jumper to 2-3 positions. .. Master Code reset to Factory .12345. and Delete All User Codes Insert the jumper RESET.. 1-2 position..5 audible beeps..Reset Master Code successful.. (after 5 seconds) ..5 audible beeps..Delete All User Codes.. Return Insert the jumper to 2-3 positions. 6. Wiring diagram: + N.O. COMN.C. PP- + N.O. COMN.C. PP- PB+ RCR- PB+ RCR- BlueRedBlackWhiteGreenBlueRedBlackWhiteGreenResetResetVoutVoutVinVinFail-SectureLocking DeviceFail-SafeLocking DevicePower SupplyPush Button 123123 Reset toFactory, or remove all stored . Master Code PIN codes Reset toFactory, or remove all stored PIN codes. Master Code Power SupplyPush Button For DC use onlyFor AC/DC Note: .. The suggested wire gauge is #22~26 AWG. .. Distance between the keypad and controller board: Maximum 50 M (cable#22~26 AWG). .. The door strike must have a vartistor or a diode across the door strike terminals to suppress the back EMF of the strike - failure to do so will damage the relay contacts and electronic components. Warranty: The product is warranted against defects in material and workmanship while used in normal service for a period of 1 year from the da...