Login:
Stimmen - 4, Durchschnittliche Bewertung: 4 ( )

Anleitung Heath Zenith, modell Decorative Wireless Chime 6280

Hersteller: Heath Zenith
Dateigröße: 228.73 kb
Dateiname:
Unterrichtssprache:enesfr
Link zum kostenlosen Download Hinweise finden Sie am Ende der Seite



Anleitung Zusammenfassung


Remove back of case by pushing in tab on bottom with a small screwdriver (see Figure 1). Make sure battery is oriented properly (See page 4). 2. Install3alkaline“D”batteries. Make sure batteries are oriented Figure 1 + + + BatteryBatteryBattery Chime Volume Jumpers - - - properly (see Figure 2). 3. Test range. Temporarily position chime and push button Cover where you want them mounted. Mounting Press push button to verify Tabs chime and push button work properly. If chime does not sound, see Troubleshooting. Figure 2 © 2007 HeathCo LLC 595-5506-11 Figure 3 4. Mount push button. Use either screws or double sided tape to mount push button. To mount with screws, remove back of case by pushing in tab on bottom with a small screwdriver. Attach back of case to door jamb or wall. Snap front of push button on. When attaching push button using double sided tape, make sure the surface of the door jamb or wall is clean. 5. Mount chime. There are two different ways to mount the chime depending upon the model of chime purchased.Determine which model you purchased below. Mount the chime according to the instructions for your chime. Chime with sawtooth hanger attached to back: 1. Drill 1/4" diameter pilot hole for wall anchor (provided) and insert anchor. 2. Screw #8 screw (provided) into anchor. Leave 1/16" gap between screw head and wall. 3. Place hanger over screw to mount chime. Sawtooth Hanger Chime Volume Jumpers 12345678 Figure 4 -2- 595-5506-11 Chime with separate cover and base: The chime base can be mounted in two different ways.The base can be mounted using the keyholes or the three mounting holes.The base may be mounted horizontally or vertically depending upon the specific model purchased. 1. Remove batteries from chime. 2. Use template on back cover for screw placement. Drill 7/32" diameter pilot holes for wall anchors (provided) and insert anchors. 3a. If using the three hole method to mount chime, insert three #6 screws (provided) through holes in back of chime. 3b. If using keyhole method to mount chime, screw two #6 screws into wall anchors. Leave 1/16" gap between screw head and wall. 4. Using arrow on template as a guide, mount chime with arrow pointing up. 5. Replace batteries (see Figure 2). Place chime cover over base. Code and Tune Settings Code Settings Note: Most installations will not require you to change any jumpers on your chime and push button. The push button and chime communicate by using a code that can be changed by removing and/or adding jumpers on both the push button and chime. The code is factory set; however, there are 128 selectable codes that allow you to expand your system and prevent outside interference. Other wireless products may cause interference and the system may not function properly. Follow the instructions below for setting a new code. 1. Open the cases and locate the jumpers on both the push button and chime (See illustration on page 4). 2. The push button and chime both have eight different jumper locations.The jumper positions 1 through 7 are used for setting the code. 3. To change the code, add and/or remove jumpers as needed. It is recommended to only change one jumper at a time and then check to see if system is functioning properly. Note: Jumpers in positions 1 through 7 must be exactly the same for both the push button and chime for this system to ...

Dieses Handbuch ist für folgende Modelle:
Haustüren und Fenster - Decorative Wireless Chime 6180 (228.73 kb)
Haustüren und Fenster - Decorative Wireless Chime 6270 (228.73 kb)

Bewertungen



Bewerten
Vorname:
Geben Sie zwei Ziffern:
capcha





Kategorien